Furuno VR-3000 Manual De Usuario
19
Error codes (con’t from previous page)
Error
Error Name
Description
Action
186
DRU Memory Shortage It looks that data cannot be recorded
more than 12 hours.
Modify radar recording setting. Max.
recordable channel: two channels.
recordable channel: two channels.
214
Battery Running
Both AC and DC power are down and
switching to battery drive. Audible
alarms are generated for max. two
switching to battery drive. Audible
alarms are generated for max. two
i
Reconnect AC and/or DC power.
218
MIC Test Fail
This ALARM is issued when the
microphone test fails. This test can
be run from Audio tab in the VDR
Maintenance Viewer, and is run every
12-hours during normal operation.
microphone test fails. This test can
be run from Audio tab in the VDR
Maintenance Viewer, and is run every
12-hours during normal operation.
Check MIC TEST in the VDR
Maintenance Viewer. If this is OK,
locate the faulty microphone and
check/replace it.
Maintenance Viewer. If this is OK,
locate the faulty microphone and
check/replace it.
226
DRU Flash Device No
match
match
This indicates that no. of FLASH
devices found in DRU and defined in
CONFIGURATION is not same.
devices found in DRU and defined in
CONFIGURATION is not same.
Check if no. of FLASH devices and
configuration setting are same.
configuration setting are same.
234
GPS No Connection
System does not receive UTC
information.
information.
Check that a valid UTC source is
connected to the serial port defined
as UTC source.
connected to the serial port defined
as UTC source.
246
PDU No Connection
Cable connection inside DCU is
faulty.
faulty.
Check cable between PDU and CPU
block in DCU.
block in DCU.
254
Self Test Fail
System failed by the self test.
Request service.
3xx
(301-372)
Serial No Connection
Data is not delivered from a serial
ohannel within an assigned time.
ohannel within an assigned time.
Reconnect serial data. Check failed
device.
device.
401
Battery No Connection
or Battery Voltage Low
or Battery Voltage Low
Battery voltage is not coming or it is
low.
low.
Confirm that the battery switch is
turned on. If ok, battery is required to
replace a new one.
turned on. If ok, battery is required to
replace a new one.
402
Terminal Board No
Connection
Connection
Terminal board is abnormal.
Confirm cable connection between
terminal board and audible interface
board.
terminal board and audible interface
board.
403
Battery Voltage Low
Batter voltage is lowered.
It is required replacement of battery.
406
DRU Exchanged
This indicates that DRU is replaced. Restart VR-3000/S
407
Backup HDD Exchanged This indicated that backup HDD is
replaced.
Restart VR-3000/S
411
Frame Grabber Board
Fail
Fail
Radar interface board is available but
it is not recognized.
it is not recognized.
Request service.
412
Audio Board Fail
Audible interface board is available
but it is not recognized.
but it is not recognized.
Request service.
413
Serial Board Fail
Serial interface board is available but
it is not recognized.
it is not recognized.
Request service.
42x
(422-428)
JB No Connection
Poor connection between JB(No.2-
8)and DCU.
8)and DCU.
Check cable and IP-address setting.
431
DCU Serial Buffer
overflow
overflow
Serial data from DCU serial channels
(1-8) aren't recorded to DRU and
Backup HDD correctly.
(1-8) aren't recorded to DRU and
Backup HDD correctly.
Restart VDR. If error occurs again,
request service.
request service.
432
JB Buffer overflow
Serial, analog and digital data from
Junction Box aren't recorded to DRU
and Backup HDD correctly.
Junction Box aren't recorded to DRU
and Backup HDD correctly.
Restart VDR. If error occurs again,
request service.
request service.