Jenn-Air DUAL-FUEL SLIDE-IN RANGE Manual De Usuario

• Check if oven controls have been prop-

erly set.

• Check to be sure plug is securely inserted

into receptacle.

• Check or re-set circuit breaker.  Check or

replace fuse.

• Check power supply.

• Check if surface and/or oven controls

have been properly set. See pgs. 4 & 6.

• Check if oven door is unlocked after self-

clean cycle.  See pg. 14.

• Check if oven is set for a delayed cook or

clean program. See pgs. 8 & 14.

• Check if Control Lock is activated. See pg.

12.

• Make sure the oven vent has not been

blocked.  See pg. 13 for location.

• Check to make sure range is level.
• Temperatures often vary between a new

oven and an old one. As ovens age, the
oven temperature often “drifts” and may
become hotter or cooler.  See pg. 12  for
instructions on adjusting the oven tem-
perature.  NOTE:  It is not recommended
to adjust the temperature if only one or
two recipes are in question.

• Check that oven temperature is decreased

by 25

°

 F when convect baking.

• See “Cooking Made Simple” booklet

for more information on bakeware and
baking.

• Make sure oven is preheated when recipe

or directions recommend preheat.

• Check rack positions. See page 13.

• Check oven rack positions. Food may be

too close to element.

• Aluminum foil was incorrectly used. Never

line the broiler insert with foil.

• Trim excess fat from meat before broiling.
• A soiled broiler pan was used.

• Check to make sure the cycle is not set for

a delayed start. See pg. 14.

• Check if door is closed.

• Longer cleaning time may be needed.
• Excessive spillovers, especially sugary and/

or acidic foods, were not removed prior
to the self-clean cycle.

• Oven interior is still hot.  Allow about one

hour for the oven to cool after the comple-
tion of a self-clean cycle. The door can be
opened when the LOC indicator word is
not displayed.

• This is normal when cooking or drying

foods high in moisture.

• Excessive moisture was used when clean-

ing the window.

• Check to be sure burner ports or ignition

ports are not clogged. See page 15.

• Check to be sure ignitor is dry and clicking.

Burner will not light if ignitor is damaged,
soiled or wet. If ignitor doesn’t click, turn
control knob OFF.

• Check to be sure a pan is sitting on the

grate above.

• Contact an authorized Jenn-Air servicer.

• Burner ports may be clogged.

• Contact an authorized Jenn-Air servicer.
• Some yellow tips on the flame are accept-

able when using LP gas.

• This is normal for a new range and will

disappear after a few uses.  Initiating a
clean cycle will “burn off” the odors more
quickly.

• Turning on a ventilation fan will help

remove the smoke and/or odor.

• Excessive food soils on the oven bottom.

Use a self-clean cycle.

• This is the cooling fan and is normal. The

fan will continue to run after use until the
oven cools.

• This is called a fault code.  If a fault code

appears in the display and beeps sound,
press the Cancel pad.  If the fault code
and beeps continue, disconnect power to
the appliance. Wait a few minutes, then
reconnect power. If fault code and beeps
still continue, disconnect power to the
appliance and call an authorized servicer.

• If the oven is heavily soiled, excessive

flare-ups may result in a fault code during
a clean cycle. Press Cancel pad and allow
the oven oven to cool completely. Wipe
out excess soil then reset the clean cycle.
If the fault code and beeps still continue,
disconnect power to the appliance and
call an authorized servicer.