Graco 311001G Manual De Usuario
Spray Tip Selection Chart
30
311001G
Spray Tip Selection Chart
Spray Tips, for use with AA Series Air Cap
AAM Fine Finish Spray Tips
Recommended for high finish quality applications at low and medium pressures. Order desired tip
(Part No. AAMxxx) from matrix below.
Recommended for high finish quality applications at low and medium pressures. Order desired tip
(Part No. AAMxxx) from matrix below.
GG4 Industrial Spray Tips
Recommended for high wear applications at high pressures. Order desired tip (Part No. GG4xxx) from matrix below.
Recommended for high wear applications at high pressures. Order desired tip (Part No. GG4xxx) from matrix below.
*
Tips are tested in water.
† These tip sizes include a 150 mesh tip filter.
‡ Do not use these tips with Model G15 guns (288844).
★
GG4 tips only.
•
All tips in the Spray Tip Selection Chart below
can be used with Model G40 guns (249242).
Use tips in the gray shaded area of the chart
with Model G40 guns only.
can be used with Model G40 guns (249242).
Use tips in the gray shaded area of the chart
with Model G40 guns only.
•
Do not use tips in the gray shaded area of the
chart with Model G15 guns (288844).
chart with Model G15 guns (288844).
SKIN INJECTION HAZARD
Do not use tips in the gray shaded area of the Spray
Tip Selection Chart with Model G15 guns (288844).
Tip Selection Chart with Model G15 guns (288844).
Failure to follow this warning can result in serious
injury or amputation.
injury or amputation.
Orifice Size in.
(mm)
* Fluid Output, fl oz/min (lpm)
Maximum Pattern Width at 12 in. (305 mm)
at 600 psi
(4.1 MPa, 41 bar)
at 1000 psi
(7.0 MPa, 70 bar)
2 to 4
(100)
4 to 6
(150)
6 to 8
(200)
8 to 10
(250)
10 to 12
(300)
12 to 14
(350)
14 to 16
(400)
16 to 18
(450)
18 to 20
(500)
† 0.007 (0.178) 4.0 (0.1)
5.2 (0.15)
★
107
207
307
† 0.009 (0.229) 7.0 (0.2)
9.1 (0.27)
109
209
309
409
509
† 0.011 (0.279) 10.0 (0.3)
13.0 (0.4)
111
211
311
411
511
611
0.013 (0.330)
13.0 (0.4)
16.9 (0.5)
213
313
413
513
613
713
0.015 (0.381)
17.0 (0.5)
22.0 (0.7)
215
315
415
515
615
715
815
0.017 (0.432)
22.0 (0.7)
28.5 (0.85)
217
317
417
517
617
717
817
917
0.019 (0.483)
28.0 (0.8)
36.3 (1.09)
219
319
419
519
619
719
819
919
0.021 (0.533)
35.0 (1.0)
45.4 (1.36)
321
421
521
621
721
821
921
‡ 0.023 (0.584) 40.0 (1.2)
51.9 (1.56)
423
523
623
723
923
‡ 0.025 (0.635) 50.0 (1.5)
64.8 (1.94)
425
625
725
825
‡ 0.027 (0.686) 58.5 (1.7)
75.8 (2.27)
527
627
827
‡ 0.029 (0.737) 68.0 (1.9)
88.2 (2.65)
629
‡ 0.031 (0.787) 78.0 (2.2)
101.1 (3.03)
431
631
‡ 0.033 (0.838) 88.0 (2.5)
114.1 (3.42)
633
★
833
‡ 0.035 (0.889) 98.0 (2.8)
127.1 (3.81)
435
‡ 0.037 (0.940) 108.0 (3.1)
140.0 (4.20)
737
‡ 0.039 (0.991) 118.0 (3.4)
153.0 (4.59)
539
639
839
Fluid output (Q) at other pressures (P) can be calculated by this formula: Q = (0.041) (QT)
where QT = fluid output (fl oz/min) from the above table for the selected orifice size.
P