Panasonic 3343109 Manual De Usuario
12. Check for damaged parts. Before using this tool, any part that appears damaged should be
carefully checked to determine that it will operate properly and perform as intended. Check for
alignment and binding of moving parts, broken parts or mounting fixtures and any other conditions
that may affect proper operation. Any part that is damaged should be properly repaired or
replaced by a qualified technician. Do not use the tool if any switch does not turn on and off
properly.
13. Replacement parts and accessories. When servicing use only identical replacement parts.
Use of other parts will void the warranty. Only use accessories intended for use with this tool.
14. Use proper size and type extension cord. If an extension cord is required. It must be of the
proper size and type to supply the correct current to the tool without heating up; otherwise, the
extension cord could melt and catch fire or cause electrical damaged to the tool. This tool
requires use of an extension cord of 0 to 10 Amps capability (up to 50 feet), with wire size rated
at 18 AWG. Longer extension cords require a larger size wire. If you are using the tool outdoors,
use an extension cord rated for outdoor use (signified by "WA" on the jacket).
15. Take caution as some woods contain preservatives such as copper chromium arsenate (CCA) which can
be toxic. When using these materials, extra care should be taken to avoid inhalation
and minimize skin contact. Wear an approved dusk mask or respirator.
16. Maintenance. For your safety, service and maintenance should be performed regularly by a
qualified technician.
carefully checked to determine that it will operate properly and perform as intended. Check for
alignment and binding of moving parts, broken parts or mounting fixtures and any other conditions
that may affect proper operation. Any part that is damaged should be properly repaired or
replaced by a qualified technician. Do not use the tool if any switch does not turn on and off
properly.
13. Replacement parts and accessories. When servicing use only identical replacement parts.
Use of other parts will void the warranty. Only use accessories intended for use with this tool.
14. Use proper size and type extension cord. If an extension cord is required. It must be of the
proper size and type to supply the correct current to the tool without heating up; otherwise, the
extension cord could melt and catch fire or cause electrical damaged to the tool. This tool
requires use of an extension cord of 0 to 10 Amps capability (up to 50 feet), with wire size rated
at 18 AWG. Longer extension cords require a larger size wire. If you are using the tool outdoors,
use an extension cord rated for outdoor use (signified by "WA" on the jacket).
15. Take caution as some woods contain preservatives such as copper chromium arsenate (CCA) which can
be toxic. When using these materials, extra care should be taken to avoid inhalation
and minimize skin contact. Wear an approved dusk mask or respirator.
16. Maintenance. For your safety, service and maintenance should be performed regularly by a
qualified technician.
ADDITIONAL SPECIFIC SAFETY INSTRUCTIONS FOR BENCH GRINDERS
1. When grinding any metals, the grinder can produce sparks which may land on your clothing or
hit your face. You should use a full face mask and appropriate protective clothing. Also ensure
that you are not operating the grinder around flammable materials of liquids. Always make sure
the safety shields and wheel guards are in place at all times. Keep guards in place and in good
working order.
2. Make sure the grinding wheels are of the proper speed (RPM) rating for the grinder.
3. Frequently quench the workpiece in water to prevent overheating; be careful not to get water
on the bench grinder.
4. Use the tool rest to steady the workpiece. If the tool rest is not used the torque of the spinning
grinding wheel may pull the workpiece from your hands.
5. Do not use aluminum oxide wheels when grinding nonferrous metals such as aluminum and
brass. Use silicon carbide wheels for nonferrous metals.
6. When buffing material, always hold the material on the lower side of the buffing wheel. Always
keep fingers clear of the grinding wheel and the tool rest.
Note: Performance of this tool may vary depending on variations in local line voltage. Extension
cord usage may also affect tool performance.
hit your face. You should use a full face mask and appropriate protective clothing. Also ensure
that you are not operating the grinder around flammable materials of liquids. Always make sure
the safety shields and wheel guards are in place at all times. Keep guards in place and in good
working order.
2. Make sure the grinding wheels are of the proper speed (RPM) rating for the grinder.
3. Frequently quench the workpiece in water to prevent overheating; be careful not to get water
on the bench grinder.
4. Use the tool rest to steady the workpiece. If the tool rest is not used the torque of the spinning
grinding wheel may pull the workpiece from your hands.
5. Do not use aluminum oxide wheels when grinding nonferrous metals such as aluminum and
brass. Use silicon carbide wheels for nonferrous metals.
6. When buffing material, always hold the material on the lower side of the buffing wheel. Always
keep fingers clear of the grinding wheel and the tool rest.
Note: Performance of this tool may vary depending on variations in local line voltage. Extension
cord usage may also affect tool performance.
WARNING
The warnings, cautions, and instructions discussed in this instruction manual cannot cover all
possible conditions and situations that may occur. It must be understood by the operator that
common sense and caution are factors which cannot be built into this product, but must be
supplied by the operator.
possible conditions and situations that may occur. It must be understood by the operator that
common sense and caution are factors which cannot be built into this product, but must be
supplied by the operator.
UNPACKING
When unpacking, check to make sure the following parts are included:
(1) 3" Bench Grinder
(1) Flex Shaft
(1 ) Wrench
(1) Grinder wheel
(1) Fiber Wheel
(2) Grinding Stone Bits
(1) 3" Bench Grinder
(1) Flex Shaft
(1 ) Wrench
(1) Grinder wheel
(1) Fiber Wheel
(2) Grinding Stone Bits
OPERATION
Turning the Bench Grinder ON and OFF
1. Insert the plug into an electrical outlet.
2. Turn the speed control knob (46) clockwise to turn the motor ON and adjust its speed.
3. To turn OFF, turn the knob counterclockwise until it clicks.
4. Never leave the bench grinder running unattended. Always turn off the tool when not in use.
1. Insert the plug into an electrical outlet.
2. Turn the speed control knob (46) clockwise to turn the motor ON and adjust its speed.
3. To turn OFF, turn the knob counterclockwise until it clicks.
4. Never leave the bench grinder running unattended. Always turn off the tool when not in use.
!
2 of 5