Hotpoint CH 10755 GF S Manual De Usuario

! Before placing your new appliance into operation please 

read these operating instructions carefully. It contains 

important information concerning the safe installation and 

operation of the appliance.

! Please keep these operating instructions for future 

reference. Make sure that the instructions are kept with the 

appliance if it is sold, given away or moved.

! The appliance must be installed by a qualified professional 

in accordance with the instructions provided.

! Any necessary adjustment or maintenance must be 

performed after the cooker has been disconnected from 

the electricity supply.

The cookers have the following technical specifications:

This appliance must be installed in accordance with the 

regulations in force and only used in a well ventilated space.

The data badge is fitted on the rear panel. The model/serial 

number can also be found on a badge located below the 

left-hand oven door beneath the door seal.

To help you make the best use of your cooker, PLEASE 

READ THIS BOOKLET CAREFULLY.

Your new cooker is guaranteed and will give lasting service. The 

guarantee is only applicable if the cooker has been installed 

in accordance with the Installation Instructions. The cooker is 

designed specifically for domestic use and responsibility will 

not be accepted for use in any other installation.

When first using the cooker ensure that the room is well 

ventilated (e.g. open a window or use an extractor fan) and that 

persons who may be sensitive to the odour avoid any fumes. It 

is suggested that any pets be removed from the room until the 

smell has ceased. This odour is due to any temporary finish 

and also any moisture absorbed by the insulation.

Our policy is one of continual improvement in design and 

development, therefore strict accuracy of illustrations and 

descriptions cannot be guaranteed.

Prior to installation, ensure that the local distribution 

conditions (nature of the gas and gas pressure) and the 

adjustment conditions are compatible. The adjustment 

conditions for this appliance are stated on the data badge 

which is fitted on the back panel.

This appliance is not designed to be connected to a 

combustion products evacuation device. It must be installed 

and connected in accordance with current installation 

regulations. particular attention should be given to the 

relevant requirements regarding ventilation.

CH10750GF S, CH10755GF S, CH10756GF S

Category I2H (GB)

This model is set to burn NATURAL GAS (G20) at 20 mbar 

It is the law that all gas appliances are installed by 

competent persons in accordance with the current edition 

of the above regulations. It is in your interest and that of 

safety to ensure compliance with the law.

In the UK, CORGI registered installers work to safe 

standards of practice.

The cooker must also be installed in accordance with Current 

national legislation.

Failure to install the cooker correctly could invalidate the 

warranty liability claims and could lead to prosecution.

The cooker may be located in a kitchen, kitchen/diner or 

a bed-sitting room, but not in a room containing a bath or 

shower. The cooker must not be installed in a bed-sitting 

room of less than 20m

3

.

The room containing the cooker should have an air supply 

in accordance with Current national legislation.

The room must have an opening window or equivalent; some 

rooms may also require a permanent vent. If the room has 

a volume between 5 and 10m

3

, it will require an air vent of 

50cm

2

 effective area unless it has a door which opens directly 

to outside. If the room has a volume of less than 5m

3

, it will 

require an air vent of 100cm

2

 effective area. If there are other 

fuel burning appliances in the same room, in accordance with 

Current national legislation should be consulted to determine 

air vent requirements.

Height:  900 - 915 mm

Widht:  1000 mm

Depth:  600 mm (excluding door handles)

Gas connection   

Rp ½ (½” BSP female)

Pressure test point 

Hotplate burner injector

Gas rate adjustment 

None

Aeration adjustment 

None

Electrical connection 

Flexible cord fitted with a 13A plug

 

 

 

230-240V~ 50Hz. 3A fuse.