Cres Cor CO151FUA12 Manual De Usuario
5925 Heisley Road • Mentor, OH 44060-1833
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
Ovens
FL-2202-MP-M
Rev. 1 (4/08)
Page 4 of 10
OPERATING INSTRUCTIONS
HOW TO START UNIT:
(for fi rst-time operation only)
A new oven needs to “burn off” factory oils and glue
before it’s fi rst use. Do NOT load food into oven until this
has been done!
A new oven needs to “burn off” factory oils and glue
before it’s fi rst use. Do NOT load food into oven until this
has been done!
Push power switch to “ON”.
Press the SELECT button and choose the TIMED
mode.
mode.
Press the COOK BUTTON and set the temperature to
350° F (177° C).
350° F (177° C).
Press the HOLD button and set the temperature to
150° F (66° C).
150° F (66° C).
Press the PROBE/TEMP button and set the time to 1
hour.
hour.
Open upper door and move thumb screw on cabinet to
open the cabinet vent.
open the cabinet vent.
Allow oven to run automatically for one hour of
COOK/RETHERM cycle and 30 minutes of HOLD
cycle.
COOK/RETHERM cycle and 30 minutes of HOLD
cycle.
HOW TO SET CONTROL:
FOR TIMED COOK OPERATION
Press the SELECT button to choose the Timed mode.
COOKING TIME
Press the PROBE/TIME button. The display will
show the cook/retherm time.
show the cook/retherm time.
Use the UP and DOWN arrows to set the desired
time.
time.
Press the SET Button to enter the time into the
control.
control.
COOKING TEMPERATURE
Press the COOK button and the display wil show the
cook/retherm temperature.
cook/retherm temperature.
Use the UP and DOWN arrows to set the desired
temperature.
temperature.
1.
2.
3.
4.
5.
6.
7.
1.
2.
3.
1.
2.
Press the SET button to enter the temperature into the
control.
control.
NOTE: Press the OVEN TEMP button at any time to
view the actual oven temperature.
view the actual oven temperature.
HOLDING TEMPERATURE
Press the HOLD button and the display will show the
holding temperature.
holding temperature.
Use the UP and DOWN buttons to set the desired
temperature.
temperature.
Press the SET button to enter the temperature into the
control.
control.
Press the START button and the display shows the
remaining time in the cook/retherm cycle.
remaining time in the cook/retherm cycle.
NOTE: The control will beep after it times down to zero
and then automatically switches to the Hold mode. The
display will then show the hold setpoint temperature.
and then automatically switches to the Hold mode. The
display will then show the hold setpoint temperature.
FOR PROBE COOK OPERATION
Press the SELECT button to choose the probe mode.
PROBE TEMPERATURE
Press the PROBE/TIME button and the display will
show the probe setpoint temperature.
show the probe setpoint temperature.
Use the UP and DOWN arrows to set the desired
temperature.
temperature.
Press the SET button to enter the temperature into the
control.
control.
NOTE: Press the OVEN TEMP button at any time to
view the actual oven temperature.
view the actual oven temperature.
Press the START button and the display will show the
actual probe temperature.
actual probe temperature.
NOTE: The control will beep when the probe setpoint
temperature has been reached and then automatically
switches to the Hold mode. The display will then show
the hold setpoint temperature.
temperature has been reached and then automatically
switches to the Hold mode. The display will then show
the hold setpoint temperature.
3.
1.
2.
3.
1.
2.
3.
Figure 1: Control Panel
(For parts description, refer to page 8.)
POWER
OFF
ON
POWER SWITCH
PRODUCT KEYS
TIME - TEMPERATURE
MODE
SELECT
START
TEMP
STOP
OVEN
PROBE
TIMED
HEAT
COOK
HOLD
SET
SETPOINTS
HOLD
PROBE
TIME
COOK
RETHERM
CONTROL