Behringer PMP6000/PMP4000/PMP1680S Manual De Usuario

Page 3 of 8

once only available in the studio is ready to 
go wherever you do. Built-in, boutique-caliber 
mic preamps with switchable +48 V phantom 
power make it possible to use either dynamic 
or condenser mics with the PMP Series. The 
PMP6000 gives you 12 mic inputs while the 
PMP4000 and PMP1680S each give you 8 mic 
inputs.

The new generation of PMP mixers come 

equipped with 24-bit FX processors, giving you  
100 mind-blowing digital effect presets such 
as delay, chorus and reverb. Apply them to 
any channel, as well as to the monitors and 
main output. In case you’re pulling double 
duty as sound engineer and performer, the FX 
processors features a footswitch jack for remote 
on/off. Of course, if you have treasured outboard 
gear you’ve grown attached to, these mixers can 
integrate them into the mix while leaving out 
the built-in FX processor.

The PMP Series gives you excellent flexibility 

to accommodate whatever a performance 
requires. You get 12 (PMP6000) or 8 (PMP4000 
and PMP1680S) channels for mics, guitars 
and other mono instruments. Stereo channels 
13-20 (PMP6000), 9-16 (PMP4000) and 
7-10 (PMP1680S) are designed to work in 
pairs as stereo channels, or independently for 
more mono instruments. All mono channels 
have 3-band EQ, switchable Low cut filter for 
eliminating infrasonics, and Clip LEDs to indicate 
when the input signal is too hot. 

A STANDBY switch (PMP6000 and PMP1680S) 

mutes all mic channels during breaks, preventing 
the microphones from picking up noise or 
interference. You can leave all faders untouched 
while you play a CD via the CD/TAPE inputs.

The FBQ Feedback Detection 

system automatically shows you which 
frequencies are causing feedback. 
Just touch the FBQ button and watch 
the red LEDs on the 7-band graphic EQ 
pinpoint show you which frequencies 
to adjust for optimized sound, 
without the feedback.

Use the CD/TAPE IN RCA inputs to feed 

in external stereo signals from CD players 
or tape decks. The VOICE CANCELLER 
switch eliminates the vocals from 

pre-recorded music for instant 
karaoke applications.

CD/TAPE OUT RCA outputs send 

line-level signals from the mixer to a 
recording device. The left and right 
main outputs can be used for a variety 
of purposes, including connecting more 
power amps. Connect monitor power 
amps or active monitor speakers to the 
MON SEND output. Powered outputs 
on these mixers are available in 
professional Speakon-compatible format 
for secure operation.

MULTI-FX 

PROCESSOR adds 

selected sound 

effect to any 

channel whose FX 

knob is turned up

GRAPHIC EQ  

adjusts specific 

frequencies

FX TO MON and 

FX TO MAIN knobs 

adjust amount of 

signal from internal 

multi-FX processor 

included in main or 

monitor mix

PHONES/CTRL 

ROOM knob 

adjusts headphone 

and control room 

output volume

VU METERS 

display main and 

monitor output 

signal levels

CD/TAPE adjusts 

volume of CD/TAPE 

IN signal in main or 

monitor mix
MAIN 2 knob 

(PMP4000/6000) 

adjusts output of 

MAIN 2 jacks

SURROUND 

knob adjusts the 

amount of stereo 

enhancement on 

the mix. Press the  

XPQ TO MAIN 

button to activate 

the effect

STANDBY 

button mutes 

all mic channels 

(PMP6000)

FX (SEND) 

fader(s) adjust 

signal sent to 

internal FX 

processor and FX 

SEND jack(s)

MON (SEND) 

fader(s) adjust 

output of MON 

SEND jacks and 

OUTPUT A when 

using MON 1/

MONO mode

MONO fader 

adjusts output 

of MONO OUT 

jack

MAIN fader(s) 

adjust the 

output of 

main signal

PHANTOM Switch 

provides 48V to  

the XLR inputs  

for use with 

condenser mics

POWER AMP 

switch selects 

operation mode of 

power amp

SPEAKER 

PROCESSING 

switch allows mixer 

to compensate 

for speakers 

with limited low 

end frequency 

response