Frigidaire FFWC38F6LS Manual De Usuario
7
tEMpERAtuRE cOntROLS
The default temperature for the wine cooler is 54°F (12°C). The temperature after power failure will be the
•
temperature set before the power failure.
To prolong the life of compressor, please wait for at least 5 minutes before the wine cooler is restarted after power
•
failure.
Failure display
If “E” and “F” are displayed, please contact local service personnel for repair.
•
If the temperature in the cooler is too low, it will display “L”.
•
If the temperature in the cooler is too high, the screen will display “H” and will flash. Under this state, the buzzer
•
will buzz for 30 seconds. One minute later, the buzzer will continue to buzz for the next 30 seconds. After three
times, the alarm will not buzz any more. You can press any key to cancel sound alarm.
Storing too many wine bottles in the cooler may cause the temperature in the cooler to rise temporarily.
Storing too many wine bottles in the cooler may cause the temperature in the cooler to rise temporarily.
•
Temperature Control for Dual Zone Model
Temperature in lower chamber indicator
Press this button once to increase temperature 1° F/C.
Press this button once to decrease temperature 1° F/C.
Temperature in upper chamber indicator
Press this button once to increase temperature 1° F/C.
Press this button once to decrease temperature 1° F/C.
Press this button once to increase temperature 1° F/C.
Press this button once to decrease temperature 1° F/C.
Temperature in upper chamber indicator
Press this button once to increase temperature 1° F/C.
Press this button once to decrease temperature 1° F/C.
Indication of Temperature in Lower Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
Indication of Temperature in Upper Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
: Temperature display.
Light: Lighting button for LED lamp; it controls the on/off of lamp.
Power: On/off button used to turn on/off all load.
Power: On/off button used to turn on/off all load.
Press
Light and Power together for 2 seconds and you can convert between
fahrenheit temperature and Celsius temperature.
Notice!
z
The default temperature is 10/10°C, and the temperature after power
failure will be the temperature set before the power failure.
z
To elongate the service life of compressor, please wait for at least 5
minutes before the wine cooler is restarted after power failure.
minutes before the wine cooler is restarted after power failure.
z
Failure display
z
If there is failure on the sensor, the screen may display failure code, such
as: E and F. When the screen displays the above-mentioned errors, please
do not disassemble it for check by yourself. You should contact local
after-sales service personnel for repair.
as: E and F. When the screen displays the above-mentioned errors, please
do not disassemble it for check by yourself. You should contact local
after-sales service personnel for repair.
z
If the temperature in the cooler is too low, it will display “L”.
When the temperature in the cooler is too high, the screen will display “H”
and will flash; under this state, the buzzer will buzz until 30 seconds; one
minute later, the buzzer will continue to give alarm in the next 30 seconds; after
the alarm is given for three times, it will not give alarm any more. You can
press any key to cancel sound alarm.
minute later, the buzzer will continue to give alarm in the next 30 seconds; after
the alarm is given for three times, it will not give alarm any more. You can
press any key to cancel sound alarm.
z
When you put a lot of wines together in the cooler, the temperature in the
cooler may rise temporarily.
cooler may rise temporarily.
- 10 -
Indication of Temperature in Lower Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
Indication of Temperature in Upper Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
: Temperature display.
Light: Lighting button for LED lamp; it controls the on/off of lamp.
Power: On/off button used to turn on/off all load.
Power: On/off button used to turn on/off all load.
Press
Light and Power together for 2 seconds and you can convert between
fahrenheit temperature and Celsius temperature.
Notice!
z
The default temperature is 10/10°C, and the temperature after power
failure will be the temperature set before the power failure.
z
To elongate the service life of compressor, please wait for at least 5
minutes before the wine cooler is restarted after power failure.
minutes before the wine cooler is restarted after power failure.
z
Failure display
z
If there is failure on the sensor, the screen may display failure code, such
as: E and F. When the screen displays the above-mentioned errors, please
do not disassemble it for check by yourself. You should contact local
after-sales service personnel for repair.
as: E and F. When the screen displays the above-mentioned errors, please
do not disassemble it for check by yourself. You should contact local
after-sales service personnel for repair.
z
If the temperature in the cooler is too low, it will display “L”.
When the temperature in the cooler is too high, the screen will display “H”
and will flash; under this state, the buzzer will buzz until 30 seconds; one
minute later, the buzzer will continue to give alarm in the next 30 seconds; after
the alarm is given for three times, it will not give alarm any more. You can
press any key to cancel sound alarm.
minute later, the buzzer will continue to give alarm in the next 30 seconds; after
the alarm is given for three times, it will not give alarm any more. You can
press any key to cancel sound alarm.
z
When you put a lot of wines together in the cooler, the temperature in the
cooler may rise temporarily.
cooler may rise temporarily.
- 10 -
Temperature display
Light: This LED turns the light ON and OFF.
Power: This LED turns the power ON and OFF.
Press both Light and Power LED’s at the same time to
Power: This LED turns the power ON and OFF.
Press both Light and Power LED’s at the same time to
change between fahrenheit and Celsius temperatures.
The default temperature is 46°F (8°C) for upper zone and 59°F (15°C) for lower zone. The temperature after
•
power failure will be the temperature set before the power failure.
To prolong the life of compressor, please wait for at least 5 minutes before the wine cooler is restarted after power
•
failure.
Failure display
If “E” and “F” are displayed, please contact local service personnel for repair.
•
If the temperature in the cooler is too low, it will display “L”.
•
If the temperature in the cooler is too high, the screen will display “H” and will flash. Under this state, the buzzer
•
will buzz for 30 seconds. One minute later, the buzzer will continue to buzz for the next 30 seconds. After three
times, the alarm will not buzz any more. You can press any key to cancel sound alarm.
Storing too many wine bottles in the cooler may cause the temperature in the cooler to rise temporarily.
Storing too many wine bottles in the cooler may cause the temperature in the cooler to rise temporarily.
•
The temperature range MIN and MAX is 41 - 54° F for the upper zone and 54 - 64° F for the lower zone.
The wine cooler can be operated by adjusting the temperature control buttons (up arrow and down arrow) until
the desired temperature is reached.
The display will flash for a few seconds before set point is locked in.
Indication of Temperature in Lower Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
Indication of Temperature in Upper Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
: Temperature display.
Light: Lighting button for LED lamp; it controls the on/off of lamp.
Power: On/off button used to turn on/off all load.
Power: On/off button used to turn on/off all load.
Press
Light and Power together for 2 seconds and you can convert between
fahrenheit temperature and Celsius temperature.
Notice!
z
The default temperature is 10/10°C, and the temperature after power
failure will be the temperature set before the power failure.
z
To elongate the service life of compressor, please wait for at least 5
minutes before the wine cooler is restarted after power failure.
minutes before the wine cooler is restarted after power failure.
z
Failure display
z
If there is failure on the sensor, the screen may display failure code, such
as: E and F. When the screen displays the above-mentioned errors, please
do not disassemble it for check by yourself. You should contact local
after-sales service personnel for repair.
as: E and F. When the screen displays the above-mentioned errors, please
do not disassemble it for check by yourself. You should contact local
after-sales service personnel for repair.
z
If the temperature in the cooler is too low, it will display “L”.
When the temperature in the cooler is too high, the screen will display “H”
and will flash; under this state, the buzzer will buzz until 30 seconds; one
minute later, the buzzer will continue to give alarm in the next 30 seconds; after
the alarm is given for three times, it will not give alarm any more. You can
press any key to cancel sound alarm.
minute later, the buzzer will continue to give alarm in the next 30 seconds; after
the alarm is given for three times, it will not give alarm any more. You can
press any key to cancel sound alarm.
z
When you put a lot of wines together in the cooler, the temperature in the
cooler may rise temporarily.
cooler may rise temporarily.
- 10 -
lower
zone
upper
zone