DeLonghi ESAM04.350 Manual De Usuario

18

19

FILL TANK

Insufficient water in the tank.

Fill the tank with water and/or insert it correctly, pushing it 

as far as it will go until it clicks into place (fig. 3).

ground Too Fine adJuST 
Mill

The grinding is too fine and the coffee is delivered too 

slowly or not at all.

repeat coffee delivery and turn the grinding adjustment 

knob one click clockwise towards “7” while the coffee mill 

is in operation.

if after making at least 2 coffees delivery is still too slow, 

repeat the correction procedure, turning the grinding 

adjustment knob another click until delivery is correct.

inSerT WaTer SPouT

The water spout is not inserted or is inserted incorrectly. 

insert water spout as far as it will go (fig. 4).

eMPTy groundS ConTainer

The grounds container is full. 

empty the grounds container and clean, then replace. 

important: when removing the drip tray, the grounds 

container MuST be emptied, even if it contains few 

grounds.  if this is not done, when you make the next 

coffees, the grounds container may fill up more than 

expected and clog the machine. (To ensure the 72 hours are 

calculated correctly, the appliance must never be turned off 

with the main switch in the 0 position.) 

72 hours have passed since the first coffee after the 

grounds container was last emptied.  

inSerT groundS ConTainer 

after cleaning, the grounds container has not been 

replaced.

open the service door, remove the drip tray and insert the 

grounds container.

add Pre-ground CoFFee

The “pre-ground coffee” function has been selected 

without placing any pre-ground coffee in the funnel.

Place pre-ground coffee in the funnel or deselect the 

“pre-ground” function.

deSCale

The machine must be descaled. 

The descaling procedure described in the “descaling” 

section needs to be performed as soon as possible.

leSS CoFFee

Too much coffee has been used.

Select a milder taste or reduce the quantity of pre-ground 

coffee.

Fill BeanS ConTainer

The coffee beans have run out.

Fill the beans container

The pre-ground coffee funnel is clogged.

empty the funnel as described in the section “Cleaning the 

pre-ground coffee funnel”.

inSerT inFuSer aSSeMBly

The infuser has not been replaced after cleaning.

insert the infuser as described in the paragraph “Cleaning 

the infuser”.

CloSe door

The service door is open

Close the service door.

INSERT MILK CONTAINER

The milk container is not inserted correctly.

insert the milk container as far as it will go. 

PreSS Clean

Milk has been delivered recently and the tubes inside the 
milk container must be cleaned. 

Press the “Clean” button and keep pressing until the 
progress bar is complete. “Cleaning underway” is displayed. 

energy Saving

The function is active and reduces electricity consumption. 

disable the function from the menu (See section “energy 

Saving”).

general alarM

The inside of the appliance is very dirty.

Clean the inside of the appliance thoroughly, as described 

in the section “Cleaning and maintenance”.  if the message 

is still displayed after cleaning, contact a service centre.

eMPTy CirCuiT Fill CirCuiT

Hot water Press OK

The water circuit is emtpy

Press OK button to deliver water from the spout until it

flows out normally. 

Below is a list of some of the possible malfunctions. if the problem cannot be resolved as described, contact Customer Services.

The coffee is not hot

The cups were not preheated.

Warm the cups by rinsing them with hot water (using the 

hot water function). 

The infuser has cooled down because 2/3 minutes have 

elapsed since the last coffee was made.

Before making the coffee, heat the infuser using the rinse 

 button.

a low coffee temperature is set. 

Set maximum coffee temperature in the menu (llll).

The coffee is not creamy 
enough.

The coffee is ground too coarsely.

Turn the grinding adjustment knob one click anticlockwise 

towards “1” while the coffee mill is in operation (fig. 

8). Continue one click at a time until coffee delivery is 

satisfactory. The effect is only visible after delivering 2 

coffees (see the section: “adjusting the coffee mill” on 

page 12).

Wrong type of coffee

use a type of coffee for espresso coffee makers.

The coffee is delivered too 
slowly or a drop at a time. 

The coffee is ground too finely.

Turn the grinding adjustment knob one click clockwise 

towards “7” while the coffee mill is in operation (fig. 11). 

Continue one click at a time until coffee delivery is 

satisfactory.  The effect is only visible after delivering 2 

coffees (see the section: “adjusting the coffee mill” on 

page 12).

The coffee does not come out 
of the spouts, but from around 
the service door.

The holes in the spouts are clogged.

Clean the spouts with a toothpick (fig. 29).

The coffee guide inside the service door is blocked.

Thoroughly clean the coffee guide, particularly near the 

hinges.

The milk contains bubbles or 
squirts out of the milk spout.

The milk is not cold enough or is not semi-skimmed.

you should ideally use skimmed or semi-skimmed milk at 

refrigerator temperature (about 5°C). 

if the result is not as you wished, try changing brand 

of milk.

The milk container lid is dirty.

Clean the milk container lid as described in the section 

“Cleaning the milk container” (page 16).

The hot water/steam nozzle is dirty

Clean the nozzle as described in the section “Cleaning the 

hot water/steam nozzle” (page 16).

The milk is not frothed.

The milk container lid is dirty.

Clean the milk container lid as described in the section 

“Cleaning the milk container” (page 16).

The hot water/steam nozzle is dirty

Clean the nozzle as described in the section “Cleaning the 

hot water/steam nozzle” (page 16).

the frothed milk regulator is in the "CaFFelaTTe" position. 

Put the milk regulator in the “CaPPuCCino” position.

The appliance does not come 
on. 

it is not plugged into the mains socket. 

Plug into the mains socket. 

The main switch is not in position i.

Place the main switch in the i position (fig. 1).

The milk does not come out of 
the milk spout.

The milk container lid is dirty.

Clean the milk container lid as described in the section 

“Cleaning the milk container” (page 16).

“energy Saving” mode is 
enabled, but the cup warmer 
is hot

a number of drinks have been prepared in rapid succession.