Beko CFD6914S Manual De Usuario
EN
12
11.Reposition plugs and hinge pin
bushings on top of doors on the
opposite side of both doors. Use small
flat-headed screwdrivers to remove
plugs and bushings. Take care not to
mark doors.(9)
12.Reposition left hand side feet
on the opposite side. Unscrew and
reposition the bottom hinge bushing.
(10)
13.Unscrew and remove the upper
door middle hinge pin bushing/
door stopper using a cross-headed
screwdriver. Important: This part
cannot be used on the opposite
side; left hand side middle hinge pin
bushing/door stopper part is supplied
in the plastic bag.(11)
14.Re-fit the upper hinge on the
left hand side using flat-headed
screwdriver.(12)
15.Fit upper door left hand side middle
hinge pin bushing/door stopper
supplied in the plastic bag using cross-
headed screwdriver.(13)
16.Reposition three small plastic
plugs on the left hand side, which
are covering middle hinge holes, on
the opposite side to cover holes left
empty.(14)
17.Locate and re-fit upper door to
upper hinge and hold the door firmly.
(15)
18.Locate the middle hinge pin to
middle hinge pin bushing of upper
door on the left hand side and re-fit the
middle hinge.(16)
19.Reposition the two screws fitted to
lower hinge holes on the left hand side
at the bottom of the cabinet on the
opposite side.(17)
bushings on top of doors on the
opposite side of both doors. Use small
flat-headed screwdrivers to remove
plugs and bushings. Take care not to
mark doors.(9)
12.Reposition left hand side feet
on the opposite side. Unscrew and
reposition the bottom hinge bushing.
(10)
13.Unscrew and remove the upper
door middle hinge pin bushing/
door stopper using a cross-headed
screwdriver. Important: This part
cannot be used on the opposite
side; left hand side middle hinge pin
bushing/door stopper part is supplied
in the plastic bag.(11)
14.Re-fit the upper hinge on the
left hand side using flat-headed
screwdriver.(12)
15.Fit upper door left hand side middle
hinge pin bushing/door stopper
supplied in the plastic bag using cross-
headed screwdriver.(13)
16.Reposition three small plastic
plugs on the left hand side, which
are covering middle hinge holes, on
the opposite side to cover holes left
empty.(14)
17.Locate and re-fit upper door to
upper hinge and hold the door firmly.
(15)
18.Locate the middle hinge pin to
middle hinge pin bushing of upper
door on the left hand side and re-fit the
middle hinge.(16)
19.Reposition the two screws fitted to
lower hinge holes on the left hand side
at the bottom of the cabinet on the
opposite side.(17)
20.Locate and re-fit lower door to
middle hinge pin and then re-fit the
lower hinge on the left hand side.(18),
(19)
21.Carefully stand the appliance
upright and adjust the two front feet if
necessary.
22.Check that doors open and close
easily, they are aligned correctly and
that there are no gaps allowing air into
the cabinet. If there are gaps between
the door seal and the cabinet, adjust
the door seal by gently pulling away
from the door using fingers.
23.Check that all the hinge screws are
tightened. Avoid over tightening the
screws.
24.Put all items, fittings back in the
appliance.
25.Fit upper door top trim and front
top panel plastic hinge covers.
Upper door top trim hinge covers are
supplied in the plastic bag.(20)
26.Wait for at least 4 hours to allow the
system to settle before switching on.
27.Once the correct storage
temperatures have been reached in
the appliance, put back all the food.
middle hinge pin and then re-fit the
lower hinge on the left hand side.(18),
(19)
21.Carefully stand the appliance
upright and adjust the two front feet if
necessary.
22.Check that doors open and close
easily, they are aligned correctly and
that there are no gaps allowing air into
the cabinet. If there are gaps between
the door seal and the cabinet, adjust
the door seal by gently pulling away
from the door using fingers.
23.Check that all the hinge screws are
tightened. Avoid over tightening the
screws.
24.Put all items, fittings back in the
appliance.
25.Fit upper door top trim and front
top panel plastic hinge covers.
Upper door top trim hinge covers are
supplied in the plastic bag.(20)
26.Wait for at least 4 hours to allow the
system to settle before switching on.
27.Once the correct storage
temperatures have been reached in
the appliance, put back all the food.