Greenheck Fan GGH20 Manual De Usuario
14
Model GGH2O
®
Installing Backsplash Panels
Flat backsplash panel
Material gauge – Stainless
Material gauge – Stainless
Insulated backsplash panel
Material gauge – Stainless
Insulation – 1 inch (25.4 mm)
Material gauge – Stainless
Insulation – 1 inch (25.4 mm)
NOTE
Panels up to 47 inches (119.4 cm) wide ship in one
piece. Over 47 inches (119.4 cm) in multiple pieces.
piece. Over 47 inches (119.4 cm) in multiple pieces.
NOTE
Panels up to 45 inches (114.3 cm) wide ship in one
piece. Over 45 inches (114.3 cm) in multiple pieces.
piece. Over 45 inches (114.3 cm) in multiple pieces.
MATERIAL GAUGE — STAINLESS
MATERIAL GAUGE — STAINLESS
INSULATION — 1 IN. (25.4 MM)
INSULATION — 1 IN. (25.4 MM)
FLAT BACKSPLASH PANEL
INSULATED BACKSPLASH PANEL
Wall
Wall
NOTE: PANELS UP TO 46 IN. (1168.4 MM) WIDE SHIP IN ONE PIECE; OVER 46 IN. (1168.4 MM) IN MULTIPLE PIECES.
NOTE: PANELS UP TO 48 IN. (1219.2 MM) WIDE SHIP IN ONE PIECE; OVER 48 IN. (1219.2 MM) IN MULTIPLE PIECES.
Length
1 inch (25.4 mm)
Heigth
Length
Height
MATERIAL GAUGE — STAINLESS
MATERIAL GAUGE — STAINLESS
INSULATION — 1 IN. (25.4 MM)
INSULATION — 1 IN. (25.4 MM)
FLAT BACKSPLASH PANEL
INSULATED BACKSPLASH PANEL
Wall
Wall
NOTE: PANELS UP TO 46 IN. (1168.4 MM) WIDE SHIP IN ONE PIECE; OVER 46 IN. (1168.4 MM) IN MULTIPLE PIECES.
NOTE: PANELS UP TO 48 IN. (1219.2 MM) WIDE SHIP IN ONE PIECE; OVER 48 IN. (1219.2 MM) IN MULTIPLE PIECES.
Length
1 inch (25.4 mm)
Heigth
Length
Height
1. After the hood is hung in position, slide the flat
flange of the backsplash panel behind the back of
the hood.
the hood.
Note: If the backsplash panel length is greater
than 45 in. (114.3 cm), it will be shipped in multiple
pieces.
than 45 in. (114.3 cm), it will be shipped in multiple
pieces.
2. After the backsplash panel has been positioned,
drill holes in the panel and fasten to the wall.
(Fasteners provided by others).
(Fasteners provided by others).
Note: The holes should be spaced to adequately
secure the panel to the wall.
secure the panel to the wall.
3. Caulk the joints between the hood and the
backsplash panel with NSF Approved silicone
caulk (GE SCS1000, or its equivalent). The caulk is
not provided.
caulk (GE SCS1000, or its equivalent). The caulk is
not provided.
4. Caulk the joint between the backsplash panels
when multiple panels are required, with NSF
Approved silicone caulk (GE SCS1000, or its
equivalent). The caulk is not provided.
Approved silicone caulk (GE SCS1000, or its
equivalent). The caulk is not provided.
Hood End Panel
Hood Front Panel
Backsplash Panel
Slide flange
behind back
of the hood.
behind back
of the hood.
Section view of
backsplash panel
overlap
backsplash panel
overlap
Holes should be spaced
to adequately secure the
panel to the wall studs.
(Hole spacing and fasteners
provided by others).
to adequately secure the
panel to the wall studs.
(Hole spacing and fasteners
provided by others).