U-Line CLRCO2175 Manual De Usuario
24
CLR2160, CLRCO2175
Troubleshooting Guide
DANGER
ELECTROCUTION HAZARD
Never attempt to repair or perform maintenance on
the unit until the main electrical power has been
disconnected.
Never attempt to repair or perform maintenance on
the unit until the main electrical power has been
disconnected.
NOTE: Recommended refrigerator temperature setting is
38°F.
38°F.
Troubleshooting - What to check when problems occur:
PROBLEM
POSSIBLE CAUSE
REMEDY
Unit does not operate and
electronic display is blank.
electronic display is blank.
No electrical supply
Plug unit in or check circuit breaker.
Low air temperature around unit
Surrounding air temperature must be at least 50°F.
No interior light (Model CLRCO2175)
No power to unit
Make sure power cord is plugged in.
Loose or burned out bulb
Tighten or replace bulb (See MAINTENANCE; LIGHT
BULB REPLACEMENT).
BULB REPLACEMENT).
Electronic display is blank and
interior light is ON with door OPEN
(Model CLRCO2175).
interior light is ON with door OPEN
(Model CLRCO2175).
A display function has changed.
Touch and hold the warmer temperature button and
touch and release the POWER button three times, then
release the temperature button. The display should
become visible.
touch and release the POWER button three times, then
release the temperature button. The display should
become visible.
Electronic display is blank with door
OPEN (Model CLR2160).
OPEN (Model CLR2160).
A display function has changed.
Touch and hold the warmer temperature button and
touch and release the POWER button three times, then
release the temperature button. The display should
become visible.
touch and release the POWER button three times, then
release the temperature button. The display should
become visible.
Electronic display shows repeating,
randomly flashing symbols and
partial characters.
randomly flashing symbols and
partial characters.
A factory control mode has been
inadvertently entered.
inadvertently entered.
Touch and hold the warmer temperature button and
touch and release the LIGHT button three times, then
release the temperature button to exit the factory
control mode. The set-point temperature should now
be displayed.
touch and release the LIGHT button three times, then
release the temperature button to exit the factory
control mode. The set-point temperature should now
be displayed.
Electronic display shows:
0, 1 to 26, or 99.
0, 1 to 26, or 99.
A factory control mode has been
inadvertently entered.
inadvertently entered.
Repeatedly touch the warmer temperature button to
advance any number shown to 99 and touch and
release the LIGHT button. The set-point temperature
should now be displayed.
advance any number shown to 99 and touch and
release the LIGHT button. The set-point temperature
should now be displayed.
Electronic display shows E3.
Door has been left open longer than
20 minutes.
20 minutes.
Close door completely. The set-point temperature
should now be displayed.
should now be displayed.
Electronic display shows one or
more of the following:
E1, E2, E4, E5, E6, E7, E8, E9, E10, P1.
more of the following:
E1, E2, E4, E5, E6, E7, E8, E9, E10, P1.
The unit is displaying an error code.
Record the error code(s) displayed and call for service.
The unit is not cold enough.
Dirty condenser coils
Clean condenser (See MAINTENANCE; CONDENSER
CLEANING).
CLEANING).
Airflow to front grille blocked
Airflow must not be obstructed to front grille (See
OPERATION).
OPERATION).
Temperature not set cold enough
(Model CLRCO2175)
(Model CLRCO2175)
Use the temperature controller to set temperature
colder. Allow 24 hours for temperature to stabilize.
colder. Allow 24 hours for temperature to stabilize.
Door is not closing completely.
Make sure no obstructions are blocking the door and
unit is level (See MAINTENANCE; LEVELING).
unit is level (See MAINTENANCE; LEVELING).
Door adjustment required (See MAINTENANCE; DOOR
ALIGNMENT CHECK AND ADJUSTMENT).
ALIGNMENT CHECK AND ADJUSTMENT).
Door gasket not sealing properly
Adjust door (See MAINTENANCE; DOOR ALIGNMENT
CHECK AND ADJUSTMENT and DOOR REVERSAL).
CHECK AND ADJUSTMENT and DOOR REVERSAL).
Noise during operation
Certain sounds are normal.
Soft sounds from the fan, water running in the ice
maker and the sound of ice dropping will be heard.
maker and the sound of ice dropping will be heard.
Fresh food section too cold (Model
CLRCO2175)
CLRCO2175)
Temperature control set too cold
Use the temperature controller to set temperature
warmer.
warmer.
Unit runs but no ice is produced.
No water being supplied to the unit
Check to see that water is connected and turned on to
the unit.
the unit.