GE ZICP720 Manual De Usuario
DIMENSIONS AND CLEARANCES
Product Clearances
These refrigerators are equipped with a 2-position
door stop. The factory set 130° door swing can be
adjusted to 90° if clearance to adjacent cabinets
or walls is restricted.
door stop. The factory set 130° door swing can be
adjusted to 90° if clearance to adjacent cabinets
or walls is restricted.
Allow 25
″ minimum clearance for a full 130° door
swing. Allow 15
″ for pan removal.
5
″ minimum clearance is required when door swing
is adjusted to 90°. If the 90° door stop position is
used, pan access is maintained, but pan removal
is restricted.
See illustrations on pages
4 and 5 to determine door
swing interaction with
adjacent cabinets or
countertops.
used, pan access is maintained, but pan removal
is restricted.
See illustrations on pages
4 and 5 to determine door
swing interaction with
adjacent cabinets or
countertops.
Design Guide
THE INSTALLATION SPACE
The installation space must be 71-1/2
″.
Water And Electrical Locations
Electrical and water supply must be located
as shown.
as shown.
The cutout depth must be 24
″
The refrigerator will project forward, slightly
beyond adjacent cabinetry, depending on your
installation.
beyond adjacent cabinetry, depending on your
installation.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot
exceed the 24
exceed the 24
″ installation depth shown. The top
case trim overlaps the bottom of the soffit.
Additional Specifications
•A separate 115 volt 60Hz., 15 or 20 amp power
supply is recommended for each product. An
individual properly grounded branch circuit or
circuit breaker is recommended. Install properly
grounded 3-prong electrical receptacles recessed
into the back wall. Electrical must be located on
rear wall as shown.
NOTE: GFI (ground fault interrupter) is not
recommended.
individual properly grounded branch circuit or
circuit breaker is recommended. Install properly
grounded 3-prong electrical receptacles recessed
into the back wall. Electrical must be located on
rear wall as shown.
NOTE: GFI (ground fault interrupter) is not
recommended.
• Both water lines can enter the opening through
the floor or back wall. Route GE SmartConnect
™
kit or 1/4
″ O.D. copper tubing between the cold
water line and the water connection location.
The tubing should be long enough to extend to
the front of the refrigerator. Installation of an
easily accessible shut-off valve in the water
line is required.
The tubing should be long enough to extend to
the front of the refrigerator. Installation of an
easily accessible shut-off valve in the water
line is required.
2-5/16"
75" From
Floor to Bottom
of Electrical Area
84-1/2" max
83-1/2" min
Finished
Opening
Opening
71-1/2" Finished Width
Electrical
24" Cutout Depth
Wall View
24-3/16"
6"
10"
6"
10"
5"
10"
10"
Water Supply
3-1/2"
3-1/2"
3-1/2"
3-1/2"
5"
3-1/2"
5"
10"
5"
3-1/2"
90° Door
Swing
Swing
* Shipping height. The
refrigerators can be
adjusted to fit into a
cutout that is 83-1/2
adjusted to fit into a
cutout that is 83-1/2
″
min. to 84-1/2
″ max.
Note that the top case
trim at the front is 1/2
trim at the front is 1/2
″
higher and will overlap
upper cabinetry or
soffit. Use leveling legs
and wheels for a
maximum 1
upper cabinetry or
soffit. Use leveling legs
and wheels for a
maximum 1
″ height
adjustment.
83-1/2
″
at Rear
28-11/16
″
Depth Including
Handles
72
″ Frame
to Frame
Width
84
″
71-1/2
″
Case Width
25-3/4
″
Case Depth
130° Door
Swing
130° Door
Swing
36-3/4
″
90°
5
″ Minimum to
Wall
3
71-1/2
″ Finished Width
2-5/16
″
Electrical
24-3/16
″
6
″
6
″
10
″
Wall View
10
″
5
″
10
″
10
″
75
″ From
Finished Floor
to Bottom of
Electrical Area
3-1/2
″
Water Supply
3-1/2
″
84-1/2
″ max
83-1/2
″ min
Finished
Opening
24
″ Cutout Depth
0
″
25
″
Min. to
Wall
25
″
Min. to
Wall
23-7/8
″
Behind
Frame
3-1/2
″
10
″
3-1/2
″ 3-1/2″
3-1/2
″
5
″
5
″
5
″