Furuno FAR-3230SW-BB Manual De Usuario
3. TARGET TRACKING (TT)
3-16
3.12
TT CPA/TCPA Alarm
The TT continuously monitors the predicted range at the Closest Point of Approach
(CPA) and predicted time to CPA (TCPA) of each TT. When the predicted CPA of any
TT becomes smaller than the preset CPA range and its predicted TCPA less than the
preset TCPA limit, the audio alarm sounds and the Alert 526 "TT CPA/TCPA" appears
in the [Alert] box. In addition, the symbol of the offending TT is red and flashes together
with its vector.
(CPA) and predicted time to CPA (TCPA) of each TT. When the predicted CPA of any
TT becomes smaller than the preset CPA range and its predicted TCPA less than the
preset TCPA limit, the audio alarm sounds and the Alert 526 "TT CPA/TCPA" appears
in the [Alert] box. In addition, the symbol of the offending TT is red and flashes together
with its vector.
This feature, when used correctly, helps prevent the risk of collision by alerting you to
threatening targets. It is important that the gain, sea clutter and rain clutter and other
radar controls are properly adjusted.
threatening targets. It is important that the gain, sea clutter and rain clutter and other
radar controls are properly adjusted.
The accuracy of TT calculations is a function of several variables including target glint,
clutter conditions and signal-to-noise ratio. The design of the TT minimizes the effects
of these variables but you must be aware that such errors will produce inaccuracies in
the derived CPA and TCPA in particular during the initial tracking period.
clutter conditions and signal-to-noise ratio. The design of the TT minimizes the effects
of these variables but you must be aware that such errors will produce inaccuracies in
the derived CPA and TCPA in particular during the initial tracking period.
CPA and TCPA settings must be set up properly taking into consideration the size,
tonnage, speed, turning performance and other characteristics of own ship.
tonnage, speed, turning performance and other characteristics of own ship.
The TT CPA/TCPA alarm should not be solely relied upon to warn you of collision sit-
uations. The operator should check all aids to navigation to monitor possible collision
situations.
uations. The operator should check all aids to navigation to monitor possible collision
situations.
3.12.1
How to set the CPA and TCPA limits
To set the CPA and TCPA ranges, do the following:
1. If the values for CPA and TCPA are
blank, click [CPA/TCPA] to show
them.
them.
2. Click the CPA indication to select
desired CPA range (0.1-20 NM).
3. Click the TCPA indication to select
desired TCPA time (1-60 minutes).
3.12.2
How to enable, disable the TT CPA/TCPA
alarm
alarm
The TT CPA/TCPA alarm can be enabled or disabled
from the TT/AIS box. Click the indication shown in the
right figure to enable or disable the TT CPA/TCPA
alarm. The alarm is disabled when the CPA and TCPA
settings are not shown.
from the TT/AIS box. Click the indication shown in the
right figure to enable or disable the TT CPA/TCPA
alarm. The alarm is disabled when the CPA and TCPA
settings are not shown.
3.12.3
How to acknowledge the TT CPA/TCPA alarm
When the CPA or TCPA of a target is within the CPA and TCPA limits, the Alert 526
"TT CPA/TCPA" appears in the [Alert] box and the audio alarm sounds. To acknowl-
edge the alarm and silence the buzzer, push the ALARM ACK key on the Control Unit,
or click the alert indication in the [Alert] box.
"TT CPA/TCPA" appears in the [Alert] box and the audio alarm sounds. To acknowl-
edge the alarm and silence the buzzer, push the ALARM ACK key on the Control Unit,
or click the alert indication in the [Alert] box.
CPA setting
TCPA setting