Garmin G1000H Manual De Usuario
190-01255-00 Rev. B
Garmin G1000H
™
Pilot’s Guide for the Bell 407GX
133
AUDIO PANEL AND CNS
VOICE RECOGNITION
Voice Recognition allows the pilot (and optionally copilot) to control the GMA 350H using spoken commands.
To activate Voice Recognition, push and hold the Push-To-Command (PTC) button while speaking a command.
When the Push-To-Command button is released, the GMA 350H will respond.
When the Push-To-Command button is released, the GMA 350H will respond.
If a command is correctly interpreted by the GMA 350H, a positive acknowlegement chime will be played,
and the pilot should verify that the correct button selection is indicated by the triangular annunciator lights.
Alternatively, some commands will be indicated by a voice response from the GMA 350H. If the desired modes
are not indicated by annunciator lights or a voice response, the pilot should repeat the command by using the
Push-To-Command button, or by manually using the front panel controls of the GMA 350H.
Alternatively, some commands will be indicated by a voice response from the GMA 350H. If the desired modes
are not indicated by annunciator lights or a voice response, the pilot should repeat the command by using the
Push-To-Command button, or by manually using the front panel controls of the GMA 350H.
If a command is incorrectly interpreted by the GMA 350H, a negative acknowlegement tone will be played.
The pilot should repeat the command by using the Push-To-Command button, or by manually using the front
panel controls of the GMA 350H. In the event of any abnormal Voice Recognition operation, at any time the
front panel controls may be used manually to control the GMA 350H.
panel controls of the GMA 350H. In the event of any abnormal Voice Recognition operation, at any time the
front panel controls may be used manually to control the GMA 350H.
The following table lists the available Voice Recognition commands, the associated actions, and the voice
response if applicable:
Control
Spoken Command
Action
Confirmation of Action
COM
“COM one”
Toggles COM1
Illuminate/Extinguish COM1 Annunciator
“MIC one”
Selects MIC1
Illuminate MIC1 Annunciator
“COM one MIC”
“COM two”
Toggles COM2
Illuminate/Extinguish COM2 Annunciator
“MIC two”
Selects MIC2
Illuminate MIC2 Annunciator
“COM two MIC”
“COM three”
Toggles COM3
Illuminate/Extinguish COM3 Annunciator
“MIC three”
Selects MIC3
Illuminate MIC3 Annunciator
“COM three MIC”
“Split COM”
Selects split COM 1/2
Illuminate MIC1/MIC2 Annunciators
“Split COM 1 2”
Selects split COM 1/2
Illuminate MIC1/MIC2 Annunciators
“Split COM 1 3”
Selects split COM 1/3
Illuminate MIC1/MIC3 Annunciators
“Split COM 2 3”
Selects split COM 2/3
Illuminate MIC2/MIC3 Annunciators
“Monitored COM mute” or
“Mute monitored COM”
Mutes monitored
COM on primary COM
reception
Voice Response:
“Monitor mute enabled”
“Disable monitored COM mute” or
“Monitored COM mute disable” or
“Disable mute monitored COM” or
“Monitored COM mute disable” or
“Disable mute monitored COM” or
“Mute monitored COM disable”
Disables monitored
COM mute on primary
COM reception
Voice Response:
“Monitor mute disabled”
NAV
“NAV one”
Toggles NAV1
Illuminate/Extinguish NAV1 Annunciator
“NAV two”
Toggles NAV2
Illuminate/Extinguish NAV2 Annunciator
AUX
“AUX” or
“Auxiliary”
Toggles AUX
Illuminate/Extinguish AUX Annunciator