Furuno 1715 Manual De Usuario
1. OPERATION
6
Manual A/C SEA adjustment
While observing the screen and the A/C
SEA tuning bar, press ◄ or ► to adjust
the A/C SEA. The setting range is 0-100.
SEA tuning bar, press ◄ or ► to adjust
the A/C SEA. The setting range is 0-100.
3. Press the [MENU/ESC] key to finish.
1.9 Suppressing Rain Clutter
The vertical beamwidth of the antenna is
designed to see surface targets even when
the ship is rolling. However, by this design the
antenna will also pick up rain clutter (rain,
snow, or hail) in the same manner as normal
targets. The illustration below shows the
appearance of rain clutter on the display.
The A/C RAIN control adjusts the receiver
sensitivity as the A/C SEA control does but
rather in a longer time period. The higher the
setting the greater the anti-clutter effect.
designed to see surface targets even when
the ship is rolling. However, by this design the
antenna will also pick up rain clutter (rain,
snow, or hail) in the same manner as normal
targets. The illustration below shows the
appearance of rain clutter on the display.
The A/C RAIN control adjusts the receiver
sensitivity as the A/C SEA control does but
rather in a longer time period. The higher the
setting the greater the anti-clutter effect.
Rain clutter at screen center
1. Press the [GAIN] key consecutively until
the display shown below appears.
A/C RAIN
[GAIN] : GAIN MENU
[MENU/ESC] : Exit.
65
A/C RAIN adjustment window
2. While observing the screen and the A/C
RAIN tuning bar, press ◄ or ► to adjust
the A/C RAIN. The setting range is 0-100.
the A/C RAIN. The setting range is 0-100.
3. Press the [MENU/ESC] key to finish.
1.10 Measuring the Range
The bearing to a target can be measured by
the range rings, by the cursor and by the
VRM (Variable Range Marker).
the range rings, by the cursor and by the
VRM (Variable Range Marker).
Measuring range by the range rings
Count the number of rings between the
center of the display and the target. Check
the range ring interval and judge the distance
of the echo from the inner edge of the nearest
ring.
center of the display and the target. Check
the range ring interval and judge the distance
of the echo from the inner edge of the nearest
ring.
Measuring range by the cursor
Operate the cursor pad to place the cursor on
the inside edge of the target. Read the range
to the cursor at the bottom right corner of the
display.
the inside edge of the target. Read the range
to the cursor at the bottom right corner of the
display.
Measuring range by the VRM
1. Press the [VRM] key to display the VRM.
The message “Place VRM by cursor”
appears and “VRM” in the EBL/VRM box
is displayed in reverse video. The
message is automatically erased after 10
seconds, or you may erase it sooner by
pressing any key.
appears and “VRM” in the EBL/VRM box
is displayed in reverse video. The
message is automatically erased after 10
seconds, or you may erase it sooner by
pressing any key.
2. Operate the cursor pad to place the VRM
on the inside edge of the target.
3. Check the VRM readout at the bottom left
corner on the screen to find the range to
the target.
the target.
To anchor the VRM, press the [VRM] key. (It
is automatically anchored if there is no key
operation for about 10 seconds.) To erase the
VRM, press the [MENU/ESC] key.
6
nm
2
Target
VRM
VRM
range
Range, bearing
and time-to-go
to cursor
location
and time-to-go
to cursor
location
RNG 3.221nm
BRG 45.6
BRG 45.6
°
TTG 00H35M
Cursor
EBL
- - -
.-
°
VRM
2.910
nm
How to measure the range