Ingersoll-Rand 67314-B Manual De Usuario

Never service or disassemble the unit or

unit components without relieving hydraulic system

pressure first. The high pressures involved could

cause serious injury.

NOTE: If this pump was purchased separately (not part

of a system), consult your sales representative for com-

patible dispensing accessories which will best match the

application. All accessories must be able to withstand the

maximum pressure developed by the pump.

A replacement warning label is available upon request,

pn \ 94576.

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET – BRYAN, OHIO 43506

(800) 276-4658 FAX (800) 266-7016

CCN 15267008

OPERATOR’S MANUAL

67314-B

INCLUDING: SPECIFICATIONS, SERVICE KITS, GENERAL INFORMATION, PARTS, TROUBLESHOOTING

RELEASED:

11-10-06

REVISED:

5-17-10

(REV. 0

67314-B

HYDRAULIC POWER MOTOR

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

SERVICE KITS

Use only genuine ARO® replacement parts to assure compat-

ible pressure rating and longest service life.

637450 pump repair kit, includes the necessary soft parts for

normal service of the entire pump.

SPECIFICATIONS

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  67314-B
Type  . . . . . . . . . . . . . . . . . . . .  Hydraulic Operated Power Motor
Motor Size . . . . . . . . . . . . . . . . . . . . . . . . . .  4.125 sq.” (26.6 sq. cm)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6” (152 mm)
Hydraulic Inlet (female)  . . . . . . . . . . . . .  1/2 - 14 N.P.T.F. - 2
Hydraulic Outlet (female)  . . . . . . . . . . .  3/4 - 14 N.P.S.M.
Pump Construction . . . . . . . . . . . . . . . . .  Carbon Steel
Dimension “A”  . . . . . . . . . . . . . . . . . . . . . .  20-13/32” (518.2 mm)
Dimension “B” . . . . . . . . . . . . . . . . . . . . . .  15-11/16” (397.8 mm)
“C” Weep Hole  . . . . . . . . . . . . . . . . . . . . . .  1/8 - 27 N.P.T.F. - 1
Motor Diameter . . . . . . . . . . . . . . . . . . . . .  8” (203.2 mm)
Maximum Temperature Limits . . . . . .  130° F (54° C)
Mounting Bracket available  . . . . . . . . 95933
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  37.75 lbs (17.1 kgs)

PERFORMANCE

Inlet Pressure Range . . . . . . . .   65 - 2000 p.s.i. (4.5 - 137.9 bar)
Required H-power @ 50 c.p.m. . . . . . .  3.2 @ 1200 (82.8 bar)
Hydraulic fl ow required @ 50 c.p.m.   11 g.p.m. (41.6 l.p.m.)
Maximum Thrust generated . . . . . . . .  8250 lbs
Maximum recommended cycles / minute . . . . . . . . .  50
Noise Level  . . . . . . . . . . . . . . . . . . . . . . . . .  N/A

GENERAL DESCRIPTION

The 4.125 square inch hydraulic motor is a general purpose
power unit and is used on many ARO industrial 2-ball, 4-ball
and chop-check pumps. It utilizes tie rod type construction
for serviceability and connects to the various lower pump
ends by tie rods.
Due to frictional losses in the system, a greater horsepower
is required to run the motor. Power supplies generating less
than shown as required in the Performance Specifications
above will work with the motor but at a reduced pressure or
cycle rate.

Figure 1

OPERATING AND SAFETY PRECAUTIONS

WARNING

READ THE GENERAL INFORMATION MAN-

UAL INCLUDED FOR ADDITIONAL OPERATING AND
SAFETY PRECAUTIONS AND OTHER IMPORTANT IN-
FORMATION.

WARNING

EXCESSIVE MATERIAL PRESSURE. Can cause

equipment failure resulting in severe injury or prop-
erty damage. Do not exceed the maximum material
pressure of any component in the system.

WARNING

A pressure relief valve must be used to pre-

vent over-pressurization of the system and possible
component rupture.

WARNING

Excessive hydraulic oil temperature can

cause fi re. The unit is rated for operation up to 130° F
(54° C). Be sure return lines are sized larger than sup-
ply lines and similarly pressure rated.

WARNING

4.125 SQ.” MOTOR
65 - 2000 P.S.I. RANGE

Hydraulic Outlet

Hydraulic Inlet