Cal Flame LTR50001038 Manual De Usuario

Barbecue Grills

LTR50001038, Rev. C

7

C

B

A

B

C

A

Connect the last open line to the side burner

(Use gas rated tape seal on all connections)

Then take other end of "T" adapter with hose attached

and connect to end of male located underneath and at

the back of the grill. (Use gas rated tape seal on all

connections).

Open barbecue door. Install hose with regulator on propane

tank. Then connect other end to "T" adapter. Make sure to 

use gas rated tape seal when installing adapter to insure

proper seal.

Grill

Items Included with Barbecue

1) "T" adapter, 3/8"

2) 2 hose fittings, 3/8”

3) Regulator with hose

NOTE:  You will need to use a gas rated

              sealer on gas connectors that are not flared.

To Propane Tank

3/8" Fittings

From Grill

From Side Burner

"T" adapter, 3/8" Threaded

To side burner, located

underneath behind burner.

To grill, located

underneath and 

behind grill

GAS LINE

GAS LINE

Assemble  a  3/8”  pipe  nipple  to  the 

1. 

3/8”  pipe  tee  using  Teflon  tape  or 

pipe sealant. Use only sealant that is 

approved for use on LP gas.
Install the pipe tee assembly to the 

2. 

grill  intake  pipe.  Tighten  assembly 

and align the branch opening of the 

tee with the hole of the cabinet.
Connect the flexible hose (male end) 

3. 

to the pipe tee.
Install the side burner into the island 

4. 

by simply setting it in place.
Connect the female end of the flexible 

5. 

hose to the side burner intake pipe.
Connect gas supply to the grill.

6. 

Check for gas leaks using soap water 

7. 

solution.

Your  Cal  Flame  grill  must  be  plugged  into  a 

permanent, grounded 110V outlet with a dedicated 

15A GFCI breaker in accordance with local codes or 

the National Electrical Code, ANSI / NFPA 70, 

or the Canadian Electrical Code, CSA C22.1.
It  is  the  owner’s  responsibility  to  ensure  that  the 

electrical  connection  to  this  appliance  is  properly 

installed.  We  recommend  a  contractor  or  licensed 

electrician install a dedicated 110V electrical service 

for your grill.
Do  not  use  an  extension  cord  to  supply  power  to 

your  Cal  Flame  grill.  Such  use  may  result  in  fire, 

electrical shock or other personal injury.

Do not install a fuse in the neutral or ground circuit. 

A fuse in the neutral or ground circuit may result in 

an electrical shock hazard.
Do not ground this appliance to a gas supply pipe or 

hot water pipe.
Use copper wire only. The use of aluminum wire may 

result in unsatisfactory connections.
Install 120VAC, 15 Amp duplex outlet in an accessible 

location under the grill inside the base enclosure. 
Locate  the  electrical  supply  box  inside  the  built-in 

enclosure  within  reach  of  the  power  cord  so  the 

connection is accessible when the grill is completely 

installed in the enclosure.

C

B

A

B

C

A

Connect the last open line to the side burner

(Use gas rated tape seal on all connections)

Then take other end of "T" adapter with hose attached

and connect to end of male located underneath and at

the back of the grill. (Use gas rated tape seal on all

connections).

Open barbecue door. Install hose with regulator on propane

tank. Then connect other end to "T" adapter. Make sure to 

use gas rated tape seal when installing adapter to insure

proper seal.

Grill

Items Included with Barbecue

1) "T" adapter, 3/8"

2) 2 hose fittings, 3/8”

3) Regulator with hose

NOTE:  You will need to use a gas rated

              sealer on gas connectors that are not flared.

To Propane Tank

3/8" Fittings

From Grill

From Side Burner

"T" adapter, 3/8" Threaded

To side burner, located

underneath behind burner.

To grill, located

underneath and 

behind grill

GAS LINE

GAS LINE