Graco 4440 Manual De Usuario

303-3-00 303199

To Attach Base

Step 1.

Place base on floor with wheels

down.

Step 2.

Open tubes of tray assembly

as shown until they latch.

Step 3.

Front tube has plastic T ends.

Tilt tray assembly as shown.

Insert one plastic T into slot

on the inside front of the base.

Repeat on opposite side, flexing

tube inward if needed to

engage the slot.

Step 4.

Lower rear tube so holes

in ends of tube line up with

two holes in back of activity

center base.
Be sure that plastic T pieces

remain in their slots.

Step 5.

Insert pin into hole

as shown, through

tray tube, and out

through base hole

on the other side.

Press firmly until tab

snaps over head of pin.

Repeat on other side.
Be sure all parts of tray

and base are securely

fastened, with T pieces

in their slots and tabs

holding pins firmly.

Push

Head

of pin

Tab holds

Avoid

serious injury or death.

DO NOT use product

without the five friction

strips under the base.

!! Make sure strips are

kept clean.

!! Clean strips with

WATER ONLY.

Step 1.

To raise your activity center,

hold the base with one hand

while lifting the tray with the

other hand.
Adjust the tray so that it is no

lower than waist level when

your child is standing in the

activity center.

Step 2.

To lower (or fold) your activity

center, reach underneath the

tray and squeeze the finger

latches, holding them in

while you lower the tray.

Tray should lower easily.

DO NOT force tray down or

unit could be damaged.

To Use Parking Stands

(on certain models)

To Adjust the Activity Center

Remove your child from the activity

center before making any adjustments.

To install parking stands (two in

the front and one in the back), lift

base slightly, depress button on

front of stands and push stands

up until they snap into place.

To use parking stands, lift base

slightly and push stands down

until they snap into place.

To release parking stands, lift

base slightly and depress button

on front of stands. Push stands

upward into storage position.

Caring for the Activity Center

Make sure five friction strips under base are kept

clean. Clean with water only.
For cleaning vinyl seat, metal and plastic parts

other than friction strips, use only household soap

or detergent and warm water. NO BLEACH.
Excessive exposure to sun or heat could cause

fading or warping of parts.

!! When parking stands are in use, it is still possible

for your child to move the activity center.

!! Be sure to engage both parking stands.

!! Never place the activity center on a table or

countertop.

Friction strips under base

Friction Strip Feature

To Attach Decal(s)

Place Graco

decal on front

of the tray as shown. Some

models also include a decal

for the base. Rub over

decal(s) with hand or clean

cloth to assure adhesion.

To Attach Seat

Step 1.

On playtray models,

remove playtray from

activity center tray by

unsnapping both side

tabs from under tray.

Step 4.

Insert the pegs on the seat

back into the four holes

located at the rear of the tray.
Underneath the tray,

insert the four screws

into the centers of the

pegs. Press down on

the seat back to help the

screws connect with

pegs. Tighten the

screws securely,

but do not

overtighten.

Bottom of

seat back

Plastic pegs

Left

bracket

Right

bracket

Bent end seated

in channel

Nut

Step 2.

With the tray assembly upside down and its front

facing you, pull up on one of the tube ends until the

tubes snap into the first height position.
Insert seat rod through hole in left bracket, then through

the tunnel of the seat.

Seat rod

inside seat

tunnel

Step 3.

Now push the threaded end of the seat rod through the

right bracket hole. Turn the bent end of the rod so it fits

securely into the left bracket channel. Push it into place.
Place nut on seat rod threads and tighten securely with

wrench or pliers.