Beko UF483APW Manual De Usuario
EN
10
Repositioning The Door
Follow the step by step instructions
and the diagram below. Numbers in
brackets refer to diagrams.
1.Switch off at the socket outlet and
pull out the mains plug.
2.Remove all food, loose items and
fittings from inside the appliance and
door shelves.
3.Carefully tilt the appliance on
its back side. (1) (You may need
somebody to help you.) Take care
not to damage the appliance by laying
on some protective material (e.g. its
original packaging). Make sure that
you tilt the appliance on its back side,
otherwise compressor oil may block
the pipes and you may damage the
appliance.
4.Unscrew and remove the LHS front
feet and bolt (2).
5.Unscrew the bolts and remove the
bottom hinge while holding the door
(3).
6.Remove the door carefully from the
top hinge by sliding down wards (4).
7.Reposition top hinge bushing
and blanking plug on the opposite
side and stand the door safely (5).
You may find it easier to remove the
bushing and the plug with the tip of
a small screwdriver. Take care not to
mark the door.
8.Reposition the top hinge on the
opposite side (6 and 7).
9.To refit the door, locate the top hinge
in the door, attach to the cabinet and
hold the door (8).
brackets refer to diagrams.
1.Switch off at the socket outlet and
pull out the mains plug.
2.Remove all food, loose items and
fittings from inside the appliance and
door shelves.
3.Carefully tilt the appliance on
its back side. (1) (You may need
somebody to help you.) Take care
not to damage the appliance by laying
on some protective material (e.g. its
original packaging). Make sure that
you tilt the appliance on its back side,
otherwise compressor oil may block
the pipes and you may damage the
appliance.
4.Unscrew and remove the LHS front
feet and bolt (2).
5.Unscrew the bolts and remove the
bottom hinge while holding the door
(3).
6.Remove the door carefully from the
top hinge by sliding down wards (4).
7.Reposition top hinge bushing
and blanking plug on the opposite
side and stand the door safely (5).
You may find it easier to remove the
bushing and the plug with the tip of
a small screwdriver. Take care not to
mark the door.
8.Reposition the top hinge on the
opposite side (6 and 7).
9.To refit the door, locate the top hinge
in the door, attach to the cabinet and
hold the door (8).
10. Fit the bottom hinge (9). If
necessary adjust and then tighten the
bolts. Ensure,that the door opens and
closes easily and that there are no
gaps allowing air into the cabinet. If
there are gaps between the door seal
and the cabinet, adjust the door seal
by gently pulling away from the door
using fingers.
11.Fit the other front feet (10).
12.Unscrew and remove the handle
(18). Do not unscrew the yellow
coloured screws!
13.Carefully stand your appliance.
(You may need somebody to help
you.) Adjust the front feet (See
Installation Instructions)
14.Put back all, loose items and
fittings.
15. Wait for at least 4 hours to allow
the system to settle before switching
on.
necessary adjust and then tighten the
bolts. Ensure,that the door opens and
closes easily and that there are no
gaps allowing air into the cabinet. If
there are gaps between the door seal
and the cabinet, adjust the door seal
by gently pulling away from the door
using fingers.
11.Fit the other front feet (10).
12.Unscrew and remove the handle
(18). Do not unscrew the yellow
coloured screws!
13.Carefully stand your appliance.
(You may need somebody to help
you.) Adjust the front feet (See
Installation Instructions)
14.Put back all, loose items and
fittings.
15. Wait for at least 4 hours to allow
the system to settle before switching
on.