Indesit KP9F11SKGS Guía Del Usuario

The switch must be suitable for the charge indicated and 

must comply with current electrical regulations (the earthing 

wire must not be interrupted by the switch). The supply cable 

must be positioned so that it does not come into contact 

with temperatures higher than 50°C at any point. 

Before connecting the appliance to the power supply, make 

sure that:

•  The appliance is earthed and the plug is compliant with 

the law.

•  The socket can withstand the maximum power of the 

appliance, which is indicated by the data plate.

•  The voltage is in the range between the values indicated 

on the data plate.

•  The socket is compatible with the plug of the appliance. 

If the socket is incompatible with the plug, ask an 

authorised technician to replace it. Do not use extension 

cords or multiple sockets.

! Once the appliance has been installed, the power supply 

cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by 

authorised technicians only.

! The manufacturer declines any liability should these 

Important: the wires in the mains lead are coloured in 

accordance with the following code:

Green & Yellow   

Blue  

 

Brown  

 

As the colours of the wires in the mains lead may not 

correspond with the coloured markings identifying the 

terminals in your plug, proceed as follows:

Connect the Green & Yellow wire to terminal marked “E” 

or 

 or coloured Green or Green & Yellow.

Connect the Brown wire to the terminal marked “L” or 

coloured Red.

Connect the Blue wire to the terminal marked “N” or 

coloured Black.

FAILURE TO OBSERVE THE ACCIDENT-PREVENTION 

REGULATIONS  RELIEVES THE  MANUFACTURER  OF 

ALL LIABILITY.

Use a rubber cable of the type H05VV-F with a cross section 

of 3 x 1.5 mm². The yellow-green earth wire must be 2 ÷ 3 

cm longer than the other wires.

Connection to the gas network or to the gas cylinder 

may be carried out using a flexible rubber or steel hose, 

in accordance with current national legislation and after 

making sure that the appliance is suited to the type of gas 

with which it will be supplied (see the rating sticker on the 

cover: if this is not the case see below). When using liquid 

gas from a cylinder, install a pressure regulator which 

complies with current national regulations.

! Make sure that the gas supply pressure is consistent 

with the values indicated in the Table of burner and nozzle 

specifications (see below). This will ensure the safe 

operation and durability of your appliance while maintaining 

efficient energy consumption. 

Make sure that the hose complies with current national 

legislation. The internal diameter of the hose must measure: 

8 mm for a liquid gas supply;13 mm for a methane gas 

supply. 

Once the connection has been performed, make sure that 

the hose:

•  Does not come into contact with any parts which reach 

temperatures of over 50°C.

•  Is not subject to any pulling or twisting forces and that it 

is not kinked or bent.

•  Does not come into contact with blades, sharp corners 

or moving parts and that it is not compressed.

•  Is  easy  to  inspect  along  its  whole  length  so  that  its 

condition may be checked.

•  Is shorter than 1500 mm.

•  Fits firmly into place at both ends, where it will be fixed 

using clamps which comply with current regulations.

! If one or more of these conditions is not fulfilled or if the 

cooker must be installed according to the conditions listed 

for class 2 - subclass 1 appliances (installed between two 

cupboards), the flexible steel hose must be used instead 

(see below).

Make sure that the hose and gaskets comply with current 

national legislation. To begin using the hose, remove the 

hose holder on the appliance (the gas supply inlet on the 

appliance is a cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose length 

does not exceed a maximum of 2 metres, making sure that 

the hose is not compressed and does not come into contact 

with moving parts.

When the installation process is complete, check the hose 

fittings for leaks using a soapy solution. Never use a flame.