Indesit IS50D1(XX)S Guía Del Usuario
GB
5
! The hob burners do not require primary air adjustment.
! After adjusting the appliance so it may be used
with a different type of gas, replace the old rating
label with a new one that corresponds to the new
type of gas (these labels are available from
Authorised Technical Assistance Centres).
! Should the gas pressure used be different (or vary
slightly) from the recommended pressure, a suitable
pressure regulator must be fitted to the inlet hose in
accordance with current national regulations relating
to “regulators for channelled gas”.
! After adjusting the appliance so it may be used
with a different type of gas, replace the old rating
label with a new one that corresponds to the new
type of gas (these labels are available from
Authorised Technical Assistance Centres).
! Should the gas pressure used be different (or vary
slightly) from the recommended pressure, a suitable
pressure regulator must be fitted to the inlet hose in
accordance with current national regulations relating
to “regulators for channelled gas”.
TECHNICAL DATA
Oven dimensions
(HxWxD)
(HxWxD)
34x39x44 cm
Volume
60 l
Useful
measurements
relating to the
oven
compartment
measurements
relating to the
oven
compartment
width 42 cm
depth 44 cm
height 23 cm
depth 44 cm
height 23 cm
Power supply
voltage and
frequency
voltage and
frequency
see data plate
Burners
may be adapted for use with any
type of gas shown on the data
plate, which is located inside the
flap or, after the oven compartment
has been opened, on the left-hand
wall inside the oven.
type of gas shown on the data
plate, which is located inside the
flap or, after the oven compartment
has been opened, on the left-hand
wall inside the oven.
ENERGY LABEL
Directive 2002/40/EC on the label
of electric ovens. Standard EN
50304
Declared energy consumption for
Natural convection Class – heating
mode:
of electric ovens. Standard EN
50304
Declared energy consumption for
Natural convection Class – heating
mode:
Static
EC Directives: 2006/95/EEC dated
12/12/06 (Low Voltage) and
subsequent amendments -
89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments -
2009/142/EC dated 30.11.09 (Gas)
and subsequent amendments -
93/68/EEC dated 22/07/93 and
subsequent amendments -
2002/96/EC.
1275/2008 (Stand-by/ Off mode)
12/12/06 (Low Voltage) and
subsequent amendments -
89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments -
2009/142/EC dated 30.11.09 (Gas)
and subsequent amendments -
93/68/EEC dated 22/07/93 and
subsequent amendments -
2002/96/EC.
1275/2008 (Stand-by/ Off mode)
Adjusting the hob burners’ minimum setting:
1. Turn the tap to the minimum position.
2. Remove the knob and adjust the regulatory
screw, which is positioned inside or next to the tap
pin, until the flame is small but steady.
! If the appliance is connected to a liquid gas
supply, the regulatory screw must be fastened as
tightly as possible.
1. Turn the tap to the minimum position.
2. Remove the knob and adjust the regulatory
screw, which is positioned inside or next to the tap
pin, until the flame is small but steady.
! If the appliance is connected to a liquid gas
supply, the regulatory screw must be fastened as
tightly as possible.
3. While the burner is alight, quickly change the position
of the knob from minimum to maximum and vice versa
several times, checking that the flame is not
extinguished.
of the knob from minimum to maximum and vice versa
several times, checking that the flame is not
extinguished.
Disposing of the appliance
When disposing of the appliance please remove the
plug by cutting the mains cable as close as
possible to the plug body and dispose of it as
described above.
Checking the connection for leaks
plug by cutting the mains cable as close as
possible to the plug body and dispose of it as
described above.
Checking the connection for leaks
When the installation process is complete, check
the hose fittings for leaks using a soapy solution.
Never use a flame.
the hose fittings for leaks using a soapy solution.
Never use a flame.
Adapting to different types of gas
It is possible to adapt the appliance to a type of gas
other than the default type (this is indicated on the
rating label on the cover).
other than the default type (this is indicated on the
rating label on the cover).
Adapting the hob
Replacing the nozzles for the hob burners:
Replacing the nozzles for the hob burners:
1. Remove the hob grids and
slide the burners off their
seats.
2. Unscrew the nozzles using
a 7 mm socket spanner (
slide the burners off their
seats.
2. Unscrew the nozzles using
a 7 mm socket spanner (
see
figure), and replace them with
nozzles suited to the new type
of gas (
nozzles suited to the new type
of gas (
see Burner and nozzle
specifications table).
3. Replace all the components by following the
above instructions in reverse.
3. Replace all the components by following the
above instructions in reverse.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE
The wires in this mains lead are coloured in
accordance with the following code:
BLUE
BLUE
BLUE
BLUE
BLUE
“NEUTRAL
NEUTRAL
NEUTRAL
NEUTRAL
NEUTRAL” (“N
N
N
N
N”)
B R O W N
B R O W N
B R O W N
B R O W N
B R O W N
“LIVE
LIVE
LIVE
LIVE
LIVE” (“LLLLL”)
GREEN AND YELLOW
GREEN AND YELLOW
GREEN AND YELLOW
GREEN AND YELLOW
GREEN AND YELLOW
“EARTH
EARTH
EARTH
EARTH
EARTH” (“E
EE
EE”)
GREEN &
YELLOW
YELLOW
BROWN
BLUE
13 amp fuse
CROSS-BAR
CORD GRIP
CORD GRIP