Snapper E281318BE Manual De Usuario
14
Section 3 - MAINTENANCE
WARNING
DO NOT attempt any adjustments, maintenance,
service or repairs with the engine running. STOP
engine. STOP blade. Engage parking brake. Remove
key. Remove spark plug wire from spark plug and
secure away from plug. Engine and components are
HOT. Avoid serious burns, allow all parts to cool
before working on machine. Fuel Filler Cap and vent
must be closed securely to prevent fuel spillage.
service or repairs with the engine running. STOP
engine. STOP blade. Engage parking brake. Remove
key. Remove spark plug wire from spark plug and
secure away from plug. Engine and components are
HOT. Avoid serious burns, allow all parts to cool
before working on machine. Fuel Filler Cap and vent
must be closed securely to prevent fuel spillage.
3.1 INTRODUCTION
To retain the quality of the Rear Engine Rider, use
genuine SNAPPER replacement parts only. Contact a
local SNAPPER dealer for parts and service assistance.
For the correct part or information for a particular Rear
Engine Riding Mower, always mention the model and
serial number. SNAPPER recommends returning the
Rear Engine Rider to an authorized SNAPPER dealer
annually for inspection and addition of any new devices
which might upgrade the safety of the Rear Engine
Rider. For the nearest SNAPPER dealer in your area,
check the yellow pages under the heading LAWN
MOWERS. For engine parts and service, look for the
engine manufacturer’s dealers under the heading,
ENGINES - gasoline.
genuine SNAPPER replacement parts only. Contact a
local SNAPPER dealer for parts and service assistance.
For the correct part or information for a particular Rear
Engine Riding Mower, always mention the model and
serial number. SNAPPER recommends returning the
Rear Engine Rider to an authorized SNAPPER dealer
annually for inspection and addition of any new devices
which might upgrade the safety of the Rear Engine
Rider. For the nearest SNAPPER dealer in your area,
check the yellow pages under the heading LAWN
MOWERS. For engine parts and service, look for the
engine manufacturer’s dealers under the heading,
ENGINES - gasoline.
3.2 SERVICE - AFTER FIRST 5 HOURS
Routine maintenance is important to the performance
and life of your Rear Engine Rider. Service performed
properly and at the recommended interval is essential.
Refer to Section “MAINTENANCE SCHEDULE” in this
manual and in the Engine Owner’s Manual. Carefully
complete all of the recommended service procedures.
3.2.1. CHANGE ENGINE OIL
1. Place bricks or wooden blocks under the front
wheels to lower rear of engine.
2. Loosen or remove oil fill cap on engine.
3. Loosen oil drain plug.
4. Place a 2 quart minimum capacity container under
the end of the oil drain. Open oil drain. See Figure 3.1
for oil drains used on the Rear Engine Riders.
and life of your Rear Engine Rider. Service performed
properly and at the recommended interval is essential.
Refer to Section “MAINTENANCE SCHEDULE” in this
manual and in the Engine Owner’s Manual. Carefully
complete all of the recommended service procedures.
3.2.1. CHANGE ENGINE OIL
1. Place bricks or wooden blocks under the front
wheels to lower rear of engine.
2. Loosen or remove oil fill cap on engine.
3. Loosen oil drain plug.
4. Place a 2 quart minimum capacity container under
the end of the oil drain. Open oil drain. See Figure 3.1
for oil drains used on the Rear Engine Riders.
FIGURE 3.1
5. After all the oil has drained, close the drain and
wipe up any oil that may have spilled. See Figure 3.1.
Dispose of used oil properly.
6. Fill engine crankcase with new oil. Refer to your
engine owner’s manual for oil specifications.
7. Change oil filter on Kohler engines at every oil
change. Refer to your engine owner’s manual for
service instructions.
wipe up any oil that may have spilled. See Figure 3.1.
Dispose of used oil properly.
6. Fill engine crankcase with new oil. Refer to your
engine owner’s manual for oil specifications.
7. Change oil filter on Kohler engines at every oil
change. Refer to your engine owner’s manual for
service instructions.
3.2.2. SERVICE ENGINE AIR CLEANER
The engine is equipped with a dual element air
cleaner. Both the foam pre-cleaner and cartridge
require service. Refer to Engine Owner’s Manual for
recommended service procedures.
3.2.3. CHECK MOWER BLADE
1. Follow WARNING statement found on this page.
2. Check fuel level in tank. If over 3/4 full, remove
tank. Refer to Section “REMOVING FUEL TANK”. If
3/4 or less, proceed to next step.
3. Carefully stand Rear Engine Rider on rear bumper.
The engine is equipped with a dual element air
cleaner. Both the foam pre-cleaner and cartridge
require service. Refer to Engine Owner’s Manual for
recommended service procedures.
3.2.3. CHECK MOWER BLADE
1. Follow WARNING statement found on this page.
2. Check fuel level in tank. If over 3/4 full, remove
tank. Refer to Section “REMOVING FUEL TANK”. If
3/4 or less, proceed to next step.
3. Carefully stand Rear Engine Rider on rear bumper.
WARNING
Remove the battery if the Rear Engine Rider will be
left standing on the rear bumper for longer than 2
hours. Refer to Section “BATTERY REMOVAL”. DO
NOT use a cutting blade that shows signs of
excessive wear or damage on the Rear Engine Rider.
Refer to Section “MOWER BLADE REPLACEMENT”
for proper blade inspection and service procedures.
left standing on the rear bumper for longer than 2
hours. Refer to Section “BATTERY REMOVAL”. DO
NOT use a cutting blade that shows signs of
excessive wear or damage on the Rear Engine Rider.
Refer to Section “MOWER BLADE REPLACEMENT”
for proper blade inspection and service procedures.
4. Check torque of blade mounting bolts. As
necessary, torque to 30 to 40 ft. lbs. See Figure 3.2.
5. Check blade for sharpness, wear and damage.
Refer to Section “BLADE WEAR LIMITS”.
necessary, torque to 30 to 40 ft. lbs. See Figure 3.2.
5. Check blade for sharpness, wear and damage.
Refer to Section “BLADE WEAR LIMITS”.
FIGURE 3.2
6. Check blade for straightness. Refer to Section
“ADJUSTING MOWER BLADE”.
“ADJUSTING MOWER BLADE”.
REMOVE OIL PLUG
TO ALLOW OIL TO
DRAIN
TO ALLOW OIL TO
DRAIN
PUSH AND ROTATE
CLOCKWISE TO
CLOSE
CLOCKWISE TO
CLOSE
ROTATE
COUNTER-
CLOCKWISE
AND PULL OUT
TO OPEN
COUNTER-
CLOCKWISE
AND PULL OUT
TO OPEN
TORQUE BLADE
MOUNTING
BOLTS TO 30 TO
40 FT. LBS.
MOUNTING
BOLTS TO 30 TO
40 FT. LBS.