GE GFB1000F Guía Del Usuario
NOTE:
Pay close attention to the order of the sink
flange parts, as they have been correctly assembled by
the factory.
the factory.
A.
Disassemble the sink flange assembly from the
disposer by turning the mount ring to the left
(clockwise) and removing it.
disposer by turning the mount ring to the left
(clockwise) and removing it.
B.
Raise the mount ring toward the top of the sink
flange. Remove the cushion mount and the mount
ring. You may want to practice installing the cushion
mount at this point before you are under the sink.
flange. Remove the cushion mount and the mount
ring. You may want to practice installing the cushion
mount at this point before you are under the sink.
C.
Unscrew the support ring from the sink flange and
remove the fiber gasket. You are now left with the
sink flange and the rubber gasket.
remove the fiber gasket. You are now left with the
sink flange and the rubber gasket.
D. The rubber gasket is used instead of plumbers putty
with stainless steel sinks. Some cast sinks will
require putty.
require putty.
E.
If no putty is used, insert the sink flange through
the rubber gasket into the sink opening. Do not
turn the flange once it is seated.
the rubber gasket into the sink opening. Do not
turn the flange once it is seated.
F.
If you use putty instead of the gasket, form a ring
around the underside of the sink flange. Insert the
flange into the sink opening, press down hard to
squeeze out excess putty. From under the sink, trim
off excess putty flush with the bottom edge of the
sink opening.
around the underside of the sink flange. Insert the
flange into the sink opening, press down hard to
squeeze out excess putty. From under the sink, trim
off excess putty flush with the bottom edge of the
sink opening.
G.
From underneath the sink,
slip the fiber gasket onto the
exposed sink flange. With
arrows pointing up, screw the
support ring onto the sink
flange and hand tighten until
the sink flange will not move. At this
point you may want to insert the stopper in the sink
and fill with water to check the sink flange seal and
insure there are no leaks.
slip the fiber gasket onto the
exposed sink flange. With
arrows pointing up, screw the
support ring onto the sink
flange and hand tighten until
the sink flange will not move. At this
point you may want to insert the stopper in the sink
and fill with water to check the sink flange seal and
insure there are no leaks.
H.
Place the mount ring over
the sink flange and hold in
place while installing the
cushion mount (large side
down). Make sure the groove
on the inside of the cushion
mount fits over the lip on the
sink flange, similar to
putting the lid on a
plastic container. Run
your fingers around the
entire cushion mount
with slight pressure.
Do not press too
hard. When the cushion mount is properly seated,
the mount ring can be pulled downward over the
cushion mount and will be free to turn.
the sink flange and hold in
place while installing the
cushion mount (large side
down). Make sure the groove
on the inside of the cushion
mount fits over the lip on the
sink flange, similar to
putting the lid on a
plastic container. Run
your fingers around the
entire cushion mount
with slight pressure.
Do not press too
hard. When the cushion mount is properly seated,
the mount ring can be pulled downward over the
cushion mount and will be free to turn.
5
Installation Instructions
COMPONENTS AND INSTALLATION
1
COMPONENTS
INSTALLATION OF SINK FLANGE
(Read completely before starting.)
Groove
Top
Bottom
Bead
Bead
Sink Flange
Rubber Gasket
Sink
Fiber Gasket
Support Ring
Open Area No Obstruction
Sink Flange
Mount Ring should be free
to move up and down
to move up and down
Cushion Mount Detail
*Stopper
*Removable
Splash Guard
Splash Guard
Sink Flange
Rubber Sink
Flange Gasket
Flange Gasket
Groove
Dishwasher
Discharge Inlet
Discharge Inlet
Elbow Gasket
Hopper
Sink
Fiber Gasket
Support Ring
(Note Arrows
Indicating Up)
(Note Arrows
Indicating Up)
Screws
Discharge
Elbow
Elbow
Elbow
Flange
Flange
Mount Ring
Rating Label
in This Area
in This Area
Tightening Ears
End Bell
(Electrical
Connections)
(Electrical
Connections)
Cushion Mount
*Not used with batch feed model
Sink Flange
Assembly
Assembly
Disposer
Hand-tighten sink
flange
flange
Correctly Installed Sink Flange
Bottom Bead of
Cushion Mount
Cushion Mount
Cushion Mount
Groove
Bottom Bead
(shown for proper orientation)