Linksys WRT54GP2 Instruccion De Instalación

c

In the DNS 1-3 fields, enter the 

DNS address(es) provided by 

your ISP. You need to enter at 

least one DNS address.

d

Click the Save Settings button.

a

If your ISP says that you are 

connecting through PPPoE or if 

you normally enter a user 

name and password to access 

the Internet, then select PPPoE 

as the Internet Connection 

Type.

b

Enter the User Name and 

Password provided by your ISP. 

(Also enter the Service Name, if 

required.)

c

Select Keep Alive if you always 

want to be connected to your 

ISP, or select Connect on 

Demand if you are charged 

for the time that you are 

connected to your ISP.

d

Click the Save Settings button. 

e

Click the Status tab and then 

the Router tab. Click the 

Connect button to start the 

connection.

C

The Router’s Web-based Utility 

will appear with the Basic Setup 

screen showing.

D

For the Internet Connection 

Type setting, six Internet 

connection types are offered 

through the drop-down menu. 

Depending on which 

connection type you select, 

the features available on the 

Basic Setup screen will differ. 

Proceed to the instructions for 

the connection type you are 

using.

a

If your ISP says that you are 

connecting through DHCP or a 

dynamic IP address from your 

ISP, then select Obtain an IP 

automatically as the Internet 

Connection Type.

b

Click the Save Settings button.

a

If your ISP says that you are 

connecting through a static or 

fixed IP address from your ISP, 

then select Static IP as the 

Internet Connection Type.

b

Enter the IP Address, Subnet 

Mask, and Gateway Address 

provided by your ISP.

PPTP is a service used in Europe and 

Israel only. If you are using a PPTP 

connection, check with your ISP for 

the necessary setup information.

RAS is a service used in Singapore 

only. If you are using a RAS 

connection, check with your ISP for 

the necessary setup information.

Heart Beat Signal is a service used in 

Australia only. If you are using a Heart 

Beat Signal connection, check with 

your ISP for the necessary setup 

information.

E

If requested by your ISP (usually 

cable ISPs), complete the Host 

Name and Domain Name 

fields. Otherwise, leave them 

blank.

F

If you haven’t already done so, 

click the Save Settings button. 

Then close the web browser.

G

Power your cable or DSL 

modem off and back on 

again.

H

Restart or power on your PCs so 

they can obtain the Router’s 

new settings.

Model No.

For additional information or troubleshooting 
help, refer to the User Guide on the Setup CD-
ROM. You can also call or e-mail for further 
support.

800-326-7114 
(toll-free from US or Canada)

support@linksys.com

http://www.linksys.com   or
http://support.linksys.com

http://www.linksys.com/support

ftp://ftp.linksys.com

800-546-5797 (800-LINKSYS)

Linksys is a registered trademark or trademark of 
Cisco Systems, Inc. and/or its affiliates in the U.S. 
and certain other countries. Copyright © 2004 
Cisco Systems, Inc. All rights reserved.

I

To test the Router’s settings, 

open your web browser from 

any computer. In the browser’s 

Address field, enter 

www.linksys.com/registration 

and press the Enter key.

Congratulations! The installation of 

the Router is complete.

WRT54GP2-QI-40521NC JL

I

NOTE: If your Internet phone service 
provider sent you the Router, then it 
may be pre-configured for you, and you 
do not need to change any settings. If 
you wish to make changes, refer to the 
instructions supplied by your Internet 
phone service provider.

If you need to manually configure the 
Router’s Internet phone service 
settings, then refer to the User Guide on 
the Setup CD. 

PPTP

Heart Beat Signal

RAS

PPPoE

Obtain an IP

Static IP

Automatically