Conairphone fx3000 Guía De Operación
USING THE PHONE ON A DESK
1. Plug the long telephone line cord into the jack in the bottom of
the BASE, thread it through the groove toward the back of the unit,
then plug it into the modular phone jack.
the BASE, thread it through the groove toward the back of the unit,
then plug it into the modular phone jack.
2. Connect the COIL CORD to the jack in the HANDSET and the
BASE.
BASE.
HANGING THE PHONE ON THE WALL
When the FX3000 is wall mounted, the HANDSET GUIDE holds the
handset in place in the cradle.
handset in place in the cradle.
On a wall phone plate
1. Plug the short telephone line cord
1. Plug the short telephone line cord
into the jack in the base bottom
and into the jack on the plate.
and into the jack on the plate.
2. Hang the base on to the two pins
and pull the base down to lock it
into position.
into position.
3. Plug the coil cord into the handset
and base jacks.
8
On a wall without a plate
1. Install 2 screws with anchors into
1. Install 2 screws with anchors into
the wall, one above the other,
3-1/4” apart, extending 3/16” out
from the wall to hold the base
securely.
3-1/4” apart, extending 3/16” out
from the wall to hold the base
securely.
2. Install the long telephone line cord
into the jack in the base, thread it
through the groove and plug it into
the modular wall jack as shown.
through the groove and plug it into
the modular wall jack as shown.
3. Hang the base on the screws and
pull it down to lock it into position.
4. Plug the coil cord into the handset
and base jacks.
TELEPHONE FEATURES
Tone/Pulse Switch
Set switch to your type of service. If you don’t know whether you
have tone or pulse:
1. Put the switch on “T” (Tone)
2. When you have a dial tone, press any key on the keypad. If the
Set switch to your type of service. If you don’t know whether you
have tone or pulse:
1. Put the switch on “T” (Tone)
2. When you have a dial tone, press any key on the keypad. If the
dial tone stops, leave it on “T” (Tone). If not, change the setting to
“P” (Pulse).
“P” (Pulse).
Receiver Volume Control
The receiver volume control is located on the handset of your
phone. This enables you to adjust the receiver volume from normal
to high for a better listening level.
The receiver volume control is located on the handset of your
phone. This enables you to adjust the receiver volume from normal
to high for a better listening level.
Ringer Off/Low/High
Your FX3000 features a harmonic dual tone ringer that can be
adjusted from a loud (HI) to a soft (LO) sound level. When you don’t
want to be disturbed, slide the switch to the OFF position. You can
still make outgoing calls without being disturbed by incoming calls.
Your FX3000 features a harmonic dual tone ringer that can be
adjusted from a loud (HI) to a soft (LO) sound level. When you don’t
want to be disturbed, slide the switch to the OFF position. You can
still make outgoing calls without being disturbed by incoming calls.
9
Once the contrast is set, the LCD shows
‘ENTER AREA CODE’ The first digit
‘-’ of the area code will blink.
Press [
‘ENTER AREA CODE’ The first digit
‘-’ of the area code will blink.
Press [
¶] or [¿] to enter the first digit of
your area code. Press [ERASE] to confirm
and go to next entry.
Repeat above steps until 3-digit area code is set.
and go to next entry.
Repeat above steps until 3-digit area code is set.
Once the area code is set, the LCD shows
‘ENTER TIME DATE’.
Press [
‘ENTER TIME DATE’.
Press [
¶] or [¿] to select the hour
digits.
Press [ERASE] to confirm and go to
the next entry.
Press [ERASE] to confirm and go to
the next entry.
Press [
¶] or [¿] to select the minute
digits.
Press [ERASE] to confirm and go to
the next entry.
Press [ERASE] to confirm and go to
the next entry.
Press [
¶] or [¿] to select the month
digits.
Press [ERASE] to confirm and go to
the next entry.
Press [ERASE] to confirm and go to
the next entry.
Press [
¶] or [¿] to select the date
digits.
Press [ERASE] to confirm.
Press [ERASE] to confirm.
The LCD shows ‘TOTAL:00 NEW:00’,
which means both the total call and
new call counter are zero.
which means both the total call and
new call counter are zero.
7