Chamberlain 955cd Manual De Usuario
To Control the Opener Lights
With SECURITY
✚
®
transmitters, a remote push button can be
programmed to operate the opener lights without opening
the door.
the door.
1. With the door closed, press and hold the remote button that
you want to control the light.
2. Press and hold the Light button on the door control.
3. Press and hold the Lock button on the door control.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener lights
should turn on or off but the door should not move.
should turn on or off but the door should not move.
Model 953CD 3-Button Security
✚
®
Remote Control
OWNER’S MANUAL
For use with 315 MHz Security
✚
®
garage door openers and
light controls that have a purple “learn” button. The code
between the remote control and the receiver changes with
each use, randomly accessing over a billion new codes.
between the remote control and the receiver changes with
each use, randomly accessing over a billion new codes.
The additional push buttons can also activate other 315 MHz
garage door openers and/or light controls. (Instructions for
programming light products are included with those
accessories.)
garage door openers and/or light controls. (Instructions for
programming light products are included with those
accessories.)
KG
1
3
9
7
5
KG
1
3
9
7
5
Instructions Are Described and Illustrated Below
1. Press and release the “learn” button on
the motor unit. The learn indicator light
will glow steadily for 30 seconds.
will glow steadily for 30 seconds.
2. Within 30 seconds, press and hold the
button on the hand-held remote.
3. Release the button when the motor unit
light blinks. It has learned the code. If
light bulbs are not installed, two clicks will
be heard.
light bulbs are not installed, two clicks will
be heard.
To Erase All Codes From Motor Unit Memory
To deactivate any unwanted remote, first erase all codes:
Press and hold the “learn” button on motor
unit until the learn indicator light goes out
(approximately 6 seconds). All previous
codes are now erased. Reprogram each
remote or keyless entry you wish to use.
unit until the learn indicator light goes out
(approximately 6 seconds). All previous
codes are now erased. Reprogram each
remote or keyless entry you wish to use.
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control
transmitters.
transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
WARNING
CAUTION
WARNING
WARNING
© 2006, Chamberlain Group Inc.
114A3206B
All Rights Reserved
FOR SERVICE DIAL OUR TOLL FREE NUMBER:
1-800-654-4736
1-800-654-4736
The Remote Control Batteries
The lithium batteries should produce
power for up to 5 years. To replace,
pry open case with visor clip or
screwdriver, as shown. Insert
batteries positive side up (+).
power for up to 5 years. To replace,
pry open case with visor clip or
screwdriver, as shown. Insert
batteries positive side up (+).
Dispose of old batteries properly.
Replacement Parts
3V2032 Lithium battery . . . . . . . . . . . . . . . . . . . . . . . . .10A20
Visor clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29B137
Visor clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29B137
Battery
positive
side up (+)
positive
side up (+)
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
• If battery is swallowed, immediately notify doctor.
WARNING
CAUTION
WARNING
WARNING
™
/
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.