Toshiba TDP T360 Manual De Usuario
4
5
Operations
Connecting the power cord
1
Insert the power cord connector
into the AC IN socket of the
projector.
2
Insert the power cord plug into a
wall or other power outlet.
Removing the lens cap
Be sure to remove the lens cap when the power is turned on. If the cap is left on the
projector, it could become deformed due to heat.
projector, it could become deformed due to heat.
Turning the power on
1
Turn on the main power switch.
The ON/STANDBY indicator will change to orange,
indicating standby mode.
indicating standby mode.
2
Press the ON/STANDBY button.
The power turns on with a beep sound (if the beep
sound is set to [
sound is set to [
On]), and the ON/STANDBY indicator
lights green. After a moment, the start-up screen
appears.
appears.
CAUTION
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyesight.
Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
Do not place your hands, face, or other objects near the air exhaust, the lamp cover or
the bottom of the unit. Doing so could result in injury and/or damage the object.
•
•
•
Turning the power on and off
Operations
Notes
The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the system to prevent
the start-up screen from appearing. To do this, use the
before this by performing any operation. You can also configure the system to prevent
the start-up screen from appearing. To do this, use the
Display setting menu
p.38
.
The first time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed
the start menu is displayed
p.26
.
You can disable the beep sound in the
Default setting 1 menu
p.41
.
When [
Key lock] is [On], the operation buttons of the projector do not work
p.43
.
When [
Password] is [On], enter password then the start-up screen is displayed after the
Password entry screen disappears
p.33
.
Do not touch the lens directly with your hand.
If fingerprints or stains are left on the projection lens surface, they may interfere with the
projector’s ability to project images on the screen.
If fingerprints or stains are left on the projection lens surface, they may interfere with the
projector’s ability to project images on the screen.
Turning the power off
1
Press the ON/STANDBY button.
A message appears on the screen, confirming that you wish to shut off the power.
To shut off the power, press the ON/STANDBY button again. If you do not wish to
shut off the power, wait for a while without conducting any operations. This message
will disappear after a moment. (This operation is no longer valid after the message
disappears.)
To shut off the power, press the ON/STANDBY button again. If you do not wish to
shut off the power, wait for a while without conducting any operations. This message
will disappear after a moment. (This operation is no longer valid after the message
disappears.)
2
Press the ON/STANDBY button again.
When the setting of beep sound is [
On], the projector beeps, and the screen
disappears, but the internal cooling fan continues to operate. Then, the projector goes
into standby mode.
During cooling, the ON/STANDBY indicator flashes. While the
indicator is flashing, the power can not be turned back on. At this
point of time, it does not matter even if you unplug the power cord.
into standby mode.
During cooling, the ON/STANDBY indicator flashes. While the
indicator is flashing, the power can not be turned back on. At this
point of time, it does not matter even if you unplug the power cord.
3
Turn off the main power switch.
4
Replace the lens cap.
After use, replace the lens cap.
Note
The projector consumes about 5W of power in standby.
We recommend that you unplug the power cord if you will not be using the projector for
an extended period.
We recommend that you unplug the power cord if you will not be using the projector for
an extended period.
Precaution
If the power cord is unplugged before cooling is complete or the main power is turned
off, give the lamp time (about 5 minutes) to cool before plugging it back in. If the lamp
overheats, it may fail to light.
off, give the lamp time (about 5 minutes) to cool before plugging it back in. If the lamp
overheats, it may fail to light.
•
•
•
•
•
•
•
•
•
•
Power cord connector
(Supplied)
Control panel
Remote
control