Toshiba 51hx93 Manual De Propietario
(E) 51/57/65HX93
Copyright © 2003 TOSHIBA CORPORATION. All rights reserved.
25
Chapter 2: Connecting your TV
After you connect your devices to the TV (pages 12–24), you will need to connect the G-LINK cable (either of the dual-wand IR
blaster cables included with your TV) from your VCR and Cable box (if applicable) to the G-LINK jack on the TV. This connection
is necessary to enable the following features of your TV Guide On Screen
blaster cables included with your TV) from your VCR and Cable box (if applicable) to the G-LINK jack on the TV. This connection
is necessary to enable the following features of your TV Guide On Screen
™
system:
• If you have a Cable box, you need to connect the G-LINK cable from the Cable box to the G-LINK jack to receive the TV Guide
On Screen system’s program listings for your Cable service.
• If you have a VCR, you need to connect the G-LINK cable from the VCR to the G-LINK jack to use the TV Guide On Screen
system’s one-touch recording feature.
G-LINK connection
This connection is necessary to enable the TV Guide On Screen™ system’s device control and one-touch recording features.
IN
ANT( 75 )
REC OUT
ANT-1
ANT-2
P
B
P
R
Y
L/
MONO
AUDIO
S-VIDEO
VIDEO 1
VIDEO 2
COLOR
STREAM
HD-1
STREAM
HD-1
COLOR
STREAM
HD-2
STREAM
HD-2
VIDEO
R
L
AUDIO
VIDEO
R
L
AUDIO
R
P
B
P
R
Y
L
AUDIO
R
VIDEO
L/
MONO
ON OFF
L
AUDIO
AUDIO
VAR
R
R
OUT
CHANNEL IN
AUDIO CENTER
DVI/HDCP IN
R
AUDIO
L
G-LINK
IR OUT
DIGITAL
AUDIO OUT
IEEE1394
1
IEEE1394
2
TheaterNet
TheaterNet
Back of TV
Front of VCR
Front of Cable box
Infrared
sensor
G-LINK (IR blaster) cable wand
(approx. 1 inch from device)
(approx. 1 inch from device)
To connect to the G-LINK jack:
1. Locate the infrared sensor on the front of your VCR or
Cable box. The sensor is marked on some devices.*
2. Align one of the G-LINK (IR blaster) cable’s wands about
1 inch away from the infrared sensor on the front of the
VCR and attach it using the included mounting tape.
If you have a Cable box, attach the other wand in a similar
manner. (See illustration at right.)
VCR and attach it using the included mounting tape.
If you have a Cable box, attach the other wand in a similar
manner. (See illustration at right.)
Note: If you do not have a Cable box, coil the second wand
with a rubber band and leave it behind the TV.
with a rubber band and leave it behind the TV.
3. Plug the G-LINK (IR blaster) cable’s plug into the TV’s
G-LINK jack.
For details on setting up the TV Guide On Screen system:
See page 36.
For details on using the TV Guide On Screen interactive
program guide:
program guide:
See page 53.
*
If you cannot locate the device’s infrared sensor:
1. Turn OFF the device.
2. Starting at the lower left corner of the device, place the end of the
device’s remote control (with the infrared emitter) so it touches the
front of the device and press POWER. (Do not use the TV’s remote
control for this step.)
front of the device and press POWER. (Do not use the TV’s remote
control for this step.)
3. If the device turns on, the place the remote control touched the
device is the location of the sensor.
4. If the device does not turn on, move the remote control slightly to the
right and press POWER again.
5. Repeat step 4 until you locate the device’s infrared sensor.