Toshiba cn32v71 Manual De Propietario
8
Using the
Remote Contr
ol
To control a cable TV converter:
Program the remote control to recognize the brand of your
converter (see “Programming the remote control for use with a
VCR or cable TV converter,” below). The shaded buttons shown
on the right will control the cable TV converter.
Set the TV/CABLE/VCR/AUX switch to the CABLE position.
converter (see “Programming the remote control for use with a
VCR or cable TV converter,” below). The shaded buttons shown
on the right will control the cable TV converter.
Set the TV/CABLE/VCR/AUX switch to the CABLE position.
Programming the remote control for use with a
VCR or a cable TV converter
VCR or a cable TV converter
This remote control is pre-programmed to operate Toshiba VCRs. To
use VCRs or cable converters other than Toshiba models, you must
follow the steps below before you operate your remote control.
use VCRs or cable converters other than Toshiba models, you must
follow the steps below before you operate your remote control.
1. Refer to the “VCR code table” or “Cable TV converter code
table” on pages 10-11 to find the number that corresponds to the
brand name of your VCR or converter.
If more than one number is listed, try each one separately until
you find the one that works.
brand name of your VCR or converter.
If more than one number is listed, try each one separately until
you find the one that works.
2. If you are reprogramming the remote control to operate your:
• VCR, set the TV/CABLE/VCR/AUX switch on the remote
control to VCR.
• cable converter, set the TV/CABLE/VCR/AUX switch on the
remote control to CABLE.
3. Hold down the RECALL button while using the Channel
Number buttons to enter the three-digit code number of your
brand of VCR or converter.
The Program Indictor lights for one second when the program-
ming is completed. When an error has occurred, the Program
Indicator blinks. Press RECALL again to reset.
brand of VCR or converter.
The Program Indictor lights for one second when the program-
ming is completed. When an error has occurred, the Program
Indicator blinks. Press RECALL again to reset.
4. Point the remote control at the VCR or converter and press
POWER to test the code number.
If the VCR or converter turns on, you have entered the right
number.
If the VCR or converter does not respond to the remote control,
you may have entered the wrong number. Repeat steps 1-4 with
another code number.
If the VCR or converter turns on, you have entered the right
number.
If the VCR or converter does not respond to the remote control,
you may have entered the wrong number. Repeat steps 1-4 with
another code number.
For future reference, write down the code numbers you used:
VCR code
VCR code
_____________________
Cable code
_____________________
CH RTN
ADV/
PIP CH
ADV/
PIP CH
LIGHT
MUTE TV/VIDEO TIMER
RECALL
POWER
CH
VOL
Channel
Number
Number
POWER
ENT
MENU/
ENTER
PLAY PIP
STOP SOURCE
FAV
FAV
EXIT
STROBE
PREVIEW
1
4
7
2
5
8
3
6
9
0
100
Enter
FAVORITE
Recall
Program
Indicator
TV
CABLE
VCR
AUX
CABLE
VCR
AUX
Note:
• Each time you replace the batteries, you
• Each time you replace the batteries, you
must reprogram the remote control.
• Some newer VCRs are capable of working
on either of two remote codes. These
VCRs have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch, it may
not respond to any of the code numbers for
your VCR brand name. In this case, set the
switch to the other position (VCR1 or
VCR2) and reprogram the remote control.
VCRs have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch, it may
not respond to any of the code numbers for
your VCR brand name. In this case, set the
switch to the other position (VCR1 or
VCR2) and reprogram the remote control.