Bazooka vr6 Prospecto
WWW.VISTAACOUSTICS.CA
8:
(Optional): Speaker performance can be enhanced by insulating the cavity
with fi berglass insulation. When installing speakers in a ceiling, it is best to install a
sheet of fi berglass insulation behind and around the back of the speaker.
sheet of fi berglass insulation behind and around the back of the speaker.
9:
Pull the cable slack through the hole in the ceiling and strip off the outer
jacket. Strip about ½” of insulation off the ends of the wires. Connect the positive wire
from the amplifi er to the red terminal on the speaker. Connect the negative wire to
the black terminal on the speaker.
from the amplifi er to the red terminal on the speaker. Connect the negative wire to
the black terminal on the speaker.
Note: Make sure the power is turned off on your amplifi er or receiver before con-
necting the speakers.
necting the speakers.
10:
Remove the speaker grill using provided tool. Place the speaker into the cut-
out in the ceiling. See fi gure D.
11:
Tighten the dogleg mounting screws evenly until the speaker is fl at against
the ceiling. If you are using a drill to tighten the screws, be sure to set the drill to its
lowest torque setting.
lowest torque setting.
12:
Make the fi nal adjustments to the pivoting tweeter and reinsert the grill into
the speaker baffl e.
VISTA ACOUSTICS VR6-VR8 OWNER’S MANUAL
Figure D: Install the speaker
Vista Acoustics® warrants to the original purchaser of this product that should the product or any part thereof be proven defective in material or workmanship within a period of 1 year
from date of purchase by original purchaser, such defects will be repaired or replaced, at the Company’s option, without charge for parts or labor.
from date of purchase by original purchaser, such defects will be repaired or replaced, at the Company’s option, without charge for parts or labor.
THIS WARRANTY DOES NOT APPLY TO ANY PRODUCT OR PART THEREOF WHICH HAS BEEN DAMAGED THROUGH ALTERATION, MISHANDLING, MISUSE, NEGLECT, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR.THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
WITHOUT LIMITATION THE IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY
IN CONTRACT OR TORT, WHETHER OR NOT ARISING FROM THE COMPANY’S NEGLIGENCE, ACTUAL OR IMPUTED. NO PERSON OR REPRESENTATIVE IS AUTHORIZED TO ASSUME FOR
THE COMPANY ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT. IN NO EVENT SHALL COMPANY BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAM-
AGES.
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR.THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
WITHOUT LIMITATION THE IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY
IN CONTRACT OR TORT, WHETHER OR NOT ARISING FROM THE COMPANY’S NEGLIGENCE, ACTUAL OR IMPUTED. NO PERSON OR REPRESENTATIVE IS AUTHORIZED TO ASSUME FOR
THE COMPANY ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT. IN NO EVENT SHALL COMPANY BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAM-
AGES.
GRILL AND TRIM
PAINTING INSTRUCTIONS:
PAINTING INSTRUCTIONS:
1. Don’t paint speakers while in-
stalled. Be sure they are removed.
stalled. Be sure they are removed.
2. Remove the grill and paint seper-
ately with two light coats.
ately with two light coats.
3. Using scissors cut out the paint
shield template provided with
speakers. Place paint shield over the
speaker area, so no paint will get on
the cone or tweeter. Paint the trim
using same method as the grill.
shield template provided with
speakers. Place paint shield over the
speaker area, so no paint will get on
the cone or tweeter. Paint the trim
using same method as the grill.
VR6 - VR8 SPECIFICATIONS: