ZyXEL 2WG Guía Del Usuario

 Chapter 15 IPSec VPN Screens

ZyWALL 2WG User’s Guide

Address Type

Use the drop-down list box to choose Single Address, Range Address, or 

Subnet Address. Select Single Address for a single IP address. Select Range 

Address for a specific range of IP addresses. Select Subnet Address to specify 

IP addresses on a network by their subnet mask.

Starting IP 

Address

When the Address Type field is configured to Single Address, enter a (static) IP 

address on the LAN behind your ZyWALL. When the Address Type field is 

configured to Range Address, enter the beginning (static) IP address, in a range 

of computers on the LAN behind your ZyWALL. When the Address Type field is 

configured to Subnet Address, this is a (static) IP address on the LAN behind 

your ZyWALL. 

Ending IP 

Address/Subnet 

Mask

When the Address Type field is configured to Single Address, this field is N/A. 

When the Address Type field is configured to Range Address, enter the end 

(static) IP address, in a range of computers on the LAN behind your ZyWALL. 

When the Address Type field is configured to Subnet Address, this is a subnet 

mask on the LAN behind your ZyWALL.

Remote Network

Specify the IP addresses of the devices behind the remote IPSec router that can 

use the VPN tunnel. The remote IP addresses must correspond to the remote 

IPSec router's configured local IP addresses. 
Two active SAs cannot have the local and remote IP address(es) both the same. 

Two active SAs can have the same local or remote IP address, but not both. You 

can configure multiple SAs between the same local and remote IP addresses, as 

long as only one is active at any time.

Address Type

Use the drop-down list box to choose Single Address, Range Address, or 

Subnet Address. Select Single Address with a single IP address. Select Range 

Address for a specific range of IP addresses. Select Subnet Address to specify 

IP addresses on a network by their subnet mask.

Starting IP 

Address

When the Address Type field is configured to Single Address, enter a (static) IP 

address on the network behind the remote IPSec router. When the Addr Type field 

is configured to Range Address, enter the beginning (static) IP address, in a 

range of computers on the network behind the remote IPSec router. When the 

Address Type field is configured to Subnet Address, enter a (static) IP address 

on the network behind the remote IPSec router. 

Ending IP 

Address/Subnet 

Mask

When the Address Type field is configured to Single Address, this field is N/A. 

When the Address Type field is configured to Range Address, enter the end 

(static) IP address, in a range of computers on the network behind the remote 

IPSec router. When the Address Type field is configured to Subnet Address, 

enter a subnet mask on the network behind the remote IPSec router. 

Gateway Policy 

Information

My ZyWALL

When the ZyWALL is in router mode, enter the WAN IP address of your ZyWALL 

or leave the field set to 0.0.0.0. 
The ZyWALL uses its current WAN IP address (static or dynamic) in setting up the 

VPN tunnel if you leave this field as 0.0.0.0. If the WAN connection goes down, the 

ZyWALL uses the dial backup IP address for the VPN tunnel when using dial 

backup or the LAN IP address when using traffic redirect.
The VPN tunnel has to be rebuilt if this IP address changes.
When the ZyWALL is in bridge mode, this field is read-only and displays the 

ZyWALL’s IP address.

Primary Remote 

Gateway 

Type the WAN IP address of the IPSec router with which you're making the VPN 

connection. 

Manual Proposal

SPI

Type a unique SPI (Security Parameter Index) from one to four characters long. 

Valid Characters are "0, 1, 2, 3, 4, 5, 6, 7, 8, and 9". 

Table 90   SECURITY > VPN > VPN Rules (Manual) > Edit (continued)