Crown i-t4000 Guía Del Usuario

Output Mode: Press an Encoder knob to select DUAL or BRIDGE (Bridge Mono). You 
will be prompted to confirm your choice. Press and hold an Encoder knob to confirm 
your choice. DUAL is the default. The Bridge indicator on the front panel will illuminate 
when the amplifier is bridged.

Input Y: Press an Encoder knob to select STEREO or Input Y. You 
will be prompted to confirm your choice. Press and hold an Encoder 
knob to confirm your choice. When INPUT Y is enabled, Channel 
1's input signal feeds both channels. STEREO is the default. (This 
screen will not display in Bridge Mono mode).

Presets: A preset is a group of DSP and amplifier settings for a particular speaker. Turn 
an Encoder to view Presets 1 through 20. To recall a preset, press the Encoder, then press 
and hold the Encoder to confirm. For more information on presets, see Section 4.3.

The preset currently in use is displayed in the upper right corner. 
(A) Active means that the amplifier is operating exactly according to that preset.
(M) Modified means that the amplifier is operating according to the preset but with 
some settings changed.
If a preset number is flashing, it is not in use.  

In the example shown below, 
• Preset 7 is in use (it’s in the upper right corner).
• The amplifier settings have been modified (M) since Preset 7 was loaded.
• The large “7” is not flashing, which means that Preset 7 is in use.
• Preset 7’s Channel-1 label is “MF–1&2”.
• Preset 7’s Channel-2 label is “MF–3&4”.

Attenuator Link: Allows either attenuator (Encoder) to control 
both channels. Push an Encoder knob to select Independent or 
Linked. Once the attenuators are linked, any difference in channel 
attenuation will be maintained, and the word LINK appears on the 
Attenuation screen.

Attenuator Limits: You can set the minimum attenuation from 0 
dB to –100 dB. This feature allows you to set a limit on the attenua-
tors. Once set, attenuation cannot be adjusted above this level. The 
attenuator limit appears as a line in the attenuator bar meter.

NOTE: The attenuator setting must be below the attenuator limit that 
you are trying to set. For example, if the attenuator is set at –3 dB, 
you cannot set the attenuator limit below –3 dB unless you also 
decrease the attenuator level.

When you see this screen, press an Encoder knob to enter the 
Advanced Menu, described next. You can go to the Advanced Menu 
screen from the Attenuation screen by pressing 
Menu/Exit > Prev > Prev.

Me/You Amp Finder: Allows users to identify a specific amplifier in 
a large network of amplifiers without having to compare address infor-
mation. Me/you can be turned on/off from software and/or the front 
panel. Press an Encoder knob to turn on the Me/You amp finder. 
When on, the menu-button LEDs flash (depending on the firmware).

To download presets for a particular loudspeaker unit, visit http://www.crownaudio.com/
amp_htm/itech-download.htm or the loudspeaker manufacturer’s website.

dB

dB

LED Meter Display Type: Press either encoder to make the 
front-panel output LEDs display average or peak values. This menu 
changes the operation of the –10 and –20 output LEDs only.

Bar Meter Display Type: You can select what the bar meters will 
display in the Attenuator Screen. Press an Encoder knob to select 
Attenuation, Input Levels, Output Levels, or Thermal %.

Attenuation is displayed as the length of the bar meters in the Atten-
uation screen that appears on startup. Input Levels and Output Lev-
els are displayed as both average and peak in the bar meters.

Thermal % indicates the amplifier temperature in percent, where 
100% is the maximum allowable temperature. If Thermal % reaches 
100%, the amplifier is out of thermal headroom and has shut down. 

Clip Limiter: Limits the output signal to prevent excessive clip-
ping. Press an Encoder knob to select ON or OFF for each channel. 
OFF is the default.

In the example shown below, you turned down an Encoder knob two notches after load-
ing Preset 7.
• Preset 7 is in use (it’s in the upper right corner).
• Preset 7 is active (A). That means the amplifier is operating exactly according to that 
preset.
• The large “5” is flashing because Preset 5 is not in use.
• Preset 5’s Channel-1 label is “LF–1&2.”
• Preset 5’s Channel-2 label is “LF–3&4.”