Crown ma-1200 Manual Suplementario
Macro-Tech 1200 Amplifier Service Manual
29
Capacitors
C01
C 8511-5
.047µF
C02
C 7964-7
.22µF
C03
C 7964-7
.22µF
C04
C 8534-7
.0047µF
C05
C 8534-7
.0047µF
C06
C 6806-1
.01µF
C07
C 6807-9
.001µF
C08
C 6810-3
180pF
C09
C 6809-5
220pF
C43
C 6806-1
.01µF
Diodes
D01
C 2851-1
1N4004
D02
C 2851-1
1N4004
D03
C 2851-1
1N4004
D04
C 2851-1
1N4004
D05
C 2851-1
1N4004
D06
C 2851-1
1N4004
D07
C 2851-1
1N4004
D08
C 2851-1
1N4004
D09
C 2851-1
1N4004
D10
C 2851-1
1N4004
D11
C 2851-1
1N4004
D12
C 2851-1
1N4004
Inductors
L00
D 6592-6
Output Coil
L01
C 3510-2
470µH
L02
C 3510-2
470µH
Transistors
Q17
C 3810-6
MPSA43/42
Q19
C 3578-9
MPSA93
Note: Q18, S100, Driver Transistors, and Output Tran-
sistors are not included with Output Module. See
Output Assembly parts list for part numbers.
sistors are not included with Output Module. See
Output Assembly parts list for part numbers.
Resistors
R00
A10266-7501
75
R01
A10266-4711
470
R02
C 7778-1
5.6 FP
R03
C 6486-2
.2 5W
R04
C 6486-2
.2 5W
R05
C 6486-2
.2 5W
R06
C 6486-2
.2 5W
R07
C 6486-2
.2 5W
R08
C 6486-2
.2 5W
R09
C 7779-9
22 FP
R10
A10266-4711
470
R11
A10266-2R74 2.7 2W
R12
A10266-1204
12 2W
R13
A10266-7501
75
R14
A10266-1204
12 2W
R15
C 6486-2
.2 5W
R16
C 6486-2
.2 5W
R17
C 6486-2
.2 5W
R18
C 6486-2
.2 5W
R19
C 6486-2
.2 5W
R20
C 6486-2
.2 5W
R21
C 7778-1
5.6 FP
R22
C 7779-9
22 FP
R23
C 6844-2
250 Pot
R24
A10266-1331
13K
R25
A10266-2221
2.2K
R26
C 6844-2
250 Pot
R27
A10266-3911
390
R28
A10266-1331
13K
R29
A10266-5101
51
R30*
A10265-10201* 102*
R35
A10266-1204
12 2W
R36
A10266-1204
12 2W
R37
A10266-1204
12 2W
R38
A10266-1204
12 2W
R39
A10266-1204
12 2W
R40
A10266-1204
12 2W
Misc.
Board
P10397-1
Jumpers
C 5868-2
0 Ohm (7)
Clips
D 6414-3
Q17/Q19
J500
J600
C 7057-0
10 Pin HDR
Note: R30 is 102 Ohms in most units, though in some
cases a different value may be used to match the
installed S100/S200 LM334 (C5826-0) device grade.
This is the standard value and is used with the most
common LM334 grade, green. If the LM334 is marked
with a blue dot, R30 should be a 107 Ohm resistor
(A10265-10701); if it is marked with a yellow dot then
R30 should be a 100 Ohm resistor (A10265-10001).
cases a different value may be used to match the
installed S100/S200 LM334 (C5826-0) device grade.
This is the standard value and is used with the most
common LM334 grade, green. If the LM334 is marked
with a blue dot, R30 should be a 107 Ohm resistor
(A10265-10701); if it is marked with a yellow dot then
R30 should be a 100 Ohm resistor (A10265-10001).
Q43202-3 Output Module (P10397-1 board) Parts List