Maytag MDB8959AWS Manual De Usuario
4
■
The amount of detergent to use depends on:
How much soil remains on the items - Heavily soiled loads
require more detergent.
require more detergent.
The hardness of the water - If you use too little in hard water,
dishes won't be clean. If you use too much in soft water,
glassware will etch.
dishes won't be clean. If you use too much in soft water,
glassware will etch.
Soft to Medium Water (0-6 grains per U.S. gallon)
[typical water softener water and some city water]
Medium to Hard Water (7-12 grains per U.S. gallon)
[well water and some city water]
[typical water softener water and some city water]
Medium to Hard Water (7-12 grains per U.S. gallon)
[well water and some city water]
■
Depending on your water hardness, fill the Main Wash section
of the dispenser as shown. Fill the Pre-Wash section to the
level shown, if needed.
of the dispenser as shown. Fill the Pre-Wash section to the
level shown, if needed.
NOTE: Fill amounts shown
are for standard powdered
detergent. Follow
instructions on the package
when using other dishwasher
detergent.
are for standard powdered
detergent. Follow
instructions on the package
when using other dishwasher
detergent.
Add Rinse Aid
Your dishwasher is designed to use rinse aid for good
drying performance. Without rinse aid your dishes and
dishwasher interior will have excessive moisture. The heat
dry option will not perform as well without rinse aid.
drying performance. Without rinse aid your dishes and
dishwasher interior will have excessive moisture. The heat
dry option will not perform as well without rinse aid.
■
Rinse aid keeps water from forming droplets that can
dry as spots or streaks. It also improves drying by
allowing water to drain off of the dishes after the final
rinse.
dry as spots or streaks. It also improves drying by
allowing water to drain off of the dishes after the final
rinse.
■
Rinse aid helps to reduce excess moisture on the dish racks
and interior of your dishwasher.
and interior of your dishwasher.
■
Check the rinse aid indicator. Add rinse aid when indicator
drops to “Refill” level.
drops to “Refill” level.
■
To add rinse aid, turn the dispenser
cap counterclockwise and lift off.
Pour rinse aid into the opening until
the indicator window looks full.
Replace the dispenser cap and turn
clockwise. Make sure cap is fully
locked.
cap counterclockwise and lift off.
Pour rinse aid into the opening until
the indicator window looks full.
Replace the dispenser cap and turn
clockwise. Make sure cap is fully
locked.
NOTE: For most water conditions,
the factory setting of 2 will give good
results. If you have hard water or
notice rings or spots, try a higher
setting. Turn the arrow adjuster
inside the dispenser by either using
your fingers or inserting a flat-blade
screwdriver into the center of the
arrow and turning.
the factory setting of 2 will give good
results. If you have hard water or
notice rings or spots, try a higher
setting. Turn the arrow adjuster
inside the dispenser by either using
your fingers or inserting a flat-blade
screwdriver into the center of the
arrow and turning.
Select a Cycle (cycles vary by model)
See “Cycle and Option Descriptions” charts in the following
section.
section.
Heavier cycles and options affect cycle length. Some cycles and
options will take up to 3
options will take up to 3
¹⁄₂ hours to complete.
Select Options (options vary by model)
See “Cycle and Option Descriptions” charts in the following
section.
section.
You can customize your cycles by pressing the options desired.
Start or Resume a Cycle
■
Run hot water at the sink nearest your dishwasher until the
water is hot. Turn off water.
water is hot. Turn off water.
■
Push door firmly closed. The door latches
automatically. Select the wash cycle and options
desired OR press START/RESUME to repeat the same
cycle and options as in the previous wash cycle.
automatically. Select the wash cycle and options
desired OR press START/RESUME to repeat the same
cycle and options as in the previous wash cycle.
■
You can add an item anytime before the main wash starts.
Open the door slowly and add the item. Close the door firmly.
Lights will stop flashing when the door is properly shut. Press
the START/RESUME button and after a slight delay, the cycle
will resume at the point of interruption.
Open the door slowly and add the item. Close the door firmly.
Lights will stop flashing when the door is properly shut. Press
the START/RESUME button and after a slight delay, the cycle
will resume at the point of interruption.
Soft Water
Hard Water
Soft Water
Hard Water
Main Wash
Pre-Wash
Full
Add
USE RINSE AID FOR
BETTER DRYING
BETTER DRYING
Lock
Open
Full
Add
¹⁄₄
turn to lock
6 5
4
3
2
- -
-
max
fill
1
- -
-
-
- - - -
-
-
-
-
STEP 3
STEP 4