Viking Range vgbq0302t Guía Del Usuario
11
Before Lighting Grill
G
e
tt
in
g
S
ta
rt
e
d
10
G
e
tt
in
g
S
ta
rt
e
d
1
2
3
5
4
6
7
9
8
10
11
12
13
14
19
18
17
16
15
1. Electronic ignition
2. Side burner control knobs
2. Side burner control knobs
(if applicable)
3. Rotisserie control knob
4. 9V battery—behind control
4. 9V battery—behind control
panel (some models)
5. Grill burner control knobs
6. Grill/smoker burner
6. Grill/smoker burner
control knob
7. 9V battery—behind control
panel
8. Interior light switch
(E-Series)
9. Porcelain grids w/stainless
steel perforated flavor
generators underneath
generators underneath
10. Smoker box
11. Rotisserie bracket
12. Rotisserie motor
13. Spit rod w/forks
14. Warming rack
11. Rotisserie bracket
12. Rotisserie motor
13. Spit rod w/forks
14. Warming rack
(if applicable)
15. Infrared rotisserie burner
16. Broiler pan
17. Interior lights (E-Series)
18. Side burner
16. Broiler pan
17. Interior lights (E-Series)
18. Side burner
(if applicable)
19. Canopy
Prior to turning on the gas, inspect the gas supply tubing or
hose. Look for evidence of abrasion, cuts, wear and tear, or
other damage which could require replacement prior to use.
Make sure all burner control knobs are off. Do not attempt to
light the burners if the smell of gas is present.
hose. Look for evidence of abrasion, cuts, wear and tear, or
other damage which could require replacement prior to use.
Make sure all burner control knobs are off. Do not attempt to
light the burners if the smell of gas is present.
Check the connection with a soap and water solution after
attaching the hose. Make sure there is gas in the tank and the
tank is upright.
attaching the hose. Make sure there is gas in the tank and the
tank is upright.
Flavor Generator Plates Proper Installation
Place the stainless steel
perforated flavor generator
plates so that the front and rear
tabs rest on the grill frame. The
flash tube must be accessible
through the plates. If the flash
tube is not accessible, the
flavor generator plates are not
properly installed.
perforated flavor generator
plates so that the front and rear
tabs rest on the grill frame. The
flash tube must be accessible
through the plates. If the flash
tube is not accessible, the
flavor generator plates are not
properly installed.
Using Grill with Outdoor
Approved Hoods
Approved Hoods
• Outdoor approved hood models should be installed in a
covered yet non-enclosed (well ventilated) area. Outdoor hoods
aid greatly in smoke and odor removal, but should not be
expected to eliminate entirely. They should also be protected
from natural elements (such as rain) as much as possible.
aid greatly in smoke and odor removal, but should not be
expected to eliminate entirely. They should also be protected
from natural elements (such as rain) as much as possible.
• Always turn the outdoor hood to the “HIGH” position
before lighting the grill.
• Keep the grill canopy closed as much as possible when
cooking so smoke is exhausted out the back of the grill. This
allows optimum performance of the hood.
allows optimum performance of the hood.
• During breezy conditions, the performance of the outdoor
hood may be compromised.
CAUTION
Wait at least five minutes before relighting a hot grill to allow
any accumulated gas to dissipate. Keep a spray bottle of
soapy water near the gas supply valve and check the
connections for gas leaks before each use.
any accumulated gas to dissipate. Keep a spray bottle of
soapy water near the gas supply valve and check the
connections for gas leaks before each use.
Flash tube
Flash tube
Flash tube
Features
NOTE: Control locations will vary according to model.