Hitachi 9es Instruccion De Instalación
Quick installation guide
Ultrastar 9ES
SCSI
Models: DDRS-34560
DDRS-39130
DDRS-39130
IBM storage products
Page 1
IBM Hard Disk Drive Technical Support Center version 3.0
Handling precautions
1. Do not cover the breather hole! Covering the
breather hole may result in loss of
breather hole may result in loss of
data.
2. Do not press on the drive! Do not apply any force
to the drive during handling or installation.
to the drive during handling or installation.
3. Always handle the drive with care to prevent
damage from shock, vibration, or electrostatic dis-
charge (ESD).
4. Do not open the static-protective bag containing the
drive until required. Static electricity can damage the
drive.
5. Turn off and unplug your computer. Remove cover.
6. When installing the drive, touch a grounded,
unpainted metal surface with the static-protective
package containing the drive for at least two seconds.
(This drains static electricity from the package and
from your body.)
7. Handle the drive carefully by the edges. Do not
touch any exposed printed circuit board.
8. Save the drive packaging material including the
ESD bag in the event that the drive must be returned.
Place the drive in an anti-static bag before placing it in
the shipping container. The warranty will be void if
the drive is not returned in IBM approved packaging.
damage from shock, vibration, or electrostatic dis-
charge (ESD).
4. Do not open the static-protective bag containing the
drive until required. Static electricity can damage the
drive.
5. Turn off and unplug your computer. Remove cover.
6. When installing the drive, touch a grounded,
unpainted metal surface with the static-protective
package containing the drive for at least two seconds.
(This drains static electricity from the package and
from your body.)
7. Handle the drive carefully by the edges. Do not
touch any exposed printed circuit board.
8. Save the drive packaging material including the
ESD bag in the event that the drive must be returned.
Place the drive in an anti-static bag before placing it in
the shipping container. The warranty will be void if
the drive is not returned in IBM approved packaging.
Installation procedure
It is advisable to backup all data before proceeding
with the installation.
with the installation.
This procedure may require use of a bootable System
Diskette containing FDISK.COM and FORMAT.COM.
Diskette containing FDISK.COM and FORMAT.COM.
Setting the address
1. Each drive on the SCSI bus must have a unique
address. Fifty pin (narrow SCSI) devices have 8 pos-
sible addresses (0-7) with address 7 (highest priority)
normally reserved for the controller. Sixty-eight and
eighty pin (wide SCSI) devices have 16 possible
addresses (0-15).
2. SCSI address bits 3 (68 & 80 pin only), 2, 1, and 0
of the 12-pin Option Jumper Block are used to select
the SCSI device ID. The shipping default is ID 6 (bits
2 and 1).
1. Each drive on the SCSI bus must have a unique
address. Fifty pin (narrow SCSI) devices have 8 pos-
sible addresses (0-7) with address 7 (highest priority)
normally reserved for the controller. Sixty-eight and
eighty pin (wide SCSI) devices have 16 possible
addresses (0-15).
2. SCSI address bits 3 (68 & 80 pin only), 2, 1, and 0
of the 12-pin Option Jumper Block are used to select
the SCSI device ID. The shipping default is ID 6 (bits
2 and 1).
Note: SCSI address bit 3 is reserved on the 50-pin models
23 (1) 24
21 (2) 22
19 (3) 20
17 (4) 18
15 (5) 16
13 (6) 14
11 (7) 12
9 (8) 10
7 (9) 8
5 (10) 6
3 (11) 4
1 (12) 2
Bit 3
Bit 2
Bit 1
Bit 0
Enable Auto Spin Up
Enable SCSI Terminator (50,68 pin)
Disable Unit Attention
Enable Auto Start Delay
Delay Start 6/12
Disable SCSI Parity Check
LED Cathod
LED Anode
Ground
Enable TI-SDTR (50-pin)
Enable TI-SDTR/WDTR (68, 80 pin)
Enable TI-SDTR/WDTR (68, 80 pin)
Logic Card
Back side of drive
Option blcok
JP1
JP12
Power
Connector
Connector
SCSI I/F
Connector
Connector