Delfield SAHRT1-S Guía De Operación
18
Delfield
Stabilizing
It is very important that all legs are properly adjusted to
keep the cabinet level, evenly distribute the weight and to
make sure the unit will not rock, lean or be unstable.
keep the cabinet level, evenly distribute the weight and to
make sure the unit will not rock, lean or be unstable.
Electrical Connection
DANGER
Refer to the amperage data list in the SPECIFICA-
TIONS or the serial tag data and your local code or
the National Electrical Code to be sure the unit is
connected to the proper power source. A protected
circuit of the correct voltage and amperage must be
run for connection of the supply cord or permanent
connection to the unit. The power must be turned
off and disconnected whenever performing mainte-
nance or repair functions.
TIONS or the serial tag data and your local code or
the National Electrical Code to be sure the unit is
connected to the proper power source. A protected
circuit of the correct voltage and amperage must be
run for connection of the supply cord or permanent
connection to the unit. The power must be turned
off and disconnected whenever performing mainte-
nance or repair functions.
CAUTION
Permanently connected units must be connected in
accordance with NEC Article 422 Appliances, C-Dis-
connecting means. It is the responsibility of the end user
to provide the disconnect means to satisfy the authority
having jurisdiction.
accordance with NEC Article 422 Appliances, C-Dis-
connecting means. It is the responsibility of the end user
to provide the disconnect means to satisfy the authority
having jurisdiction.
The power cords supplied with this equipment are three-
pronged plugs and must be connected to a three-pronged
wall outlet for proper grounding. Do not use an adapter
to connect to a two-pronged outlet. The three pronged-
outlet provides a ground connection which must be
used to prevent a shock hazard.
pronged plugs and must be connected to a three-pronged
wall outlet for proper grounding. Do not use an adapter
to connect to a two-pronged outlet. The three pronged-
outlet provides a ground connection which must be
used to prevent a shock hazard.
CAUTION
Have the wall outlet checked by a qualified electrician to
be sure a proper ground is present and that the outlet
provides the correct voltage and required amperage to
match the rating plate.
be sure a proper ground is present and that the outlet
provides the correct voltage and required amperage to
match the rating plate.
Any power cord that is frayed or damaged should be
replaced. When disconnecting the unit from the power
source, do not pull on the wire. Firmly grip the plug and
remove from outlet.
replaced. When disconnecting the unit from the power
source, do not pull on the wire. Firmly grip the plug and
remove from outlet.
The plugs shown in Figure 3 are used on the various models.
ROLL-INS AND ROLL-THRU MODELS
Location
Cabinets represented in this manual are intended for
indoor use only. Be sure the location chosen has a floor
strong enough to support the total weight of the cabinet.
Allow for a total load of approximately 1000 pounds
(450 kg) per door section. Reinforce the floor if necessary
indoor use only. Be sure the location chosen has a floor
strong enough to support the total weight of the cabinet.
Allow for a total load of approximately 1000 pounds
(450 kg) per door section. Reinforce the floor if necessary
to provide for maximum loading. For the most efficient
operation, be sure to provide good air circulation inside
and out. The location should be selected so that the
power cord can be connected without any extensions.
operation, be sure to provide good air circulation inside
and out. The location should be selected so that the
power cord can be connected without any extensions.
Inside Cabinet
Take care not to block airflow to the fans or heating
elements and allow space along the front, back and sides.
elements and allow space along the front, back and sides.
Outside Cabinet
Be sure that the unit has access to ample air; avoid hot
corners and locations near stoves and ovens. Provide a
minimum clearance of 12" (30.5 cm) above the unit that
is open to the front.
corners and locations near stoves and ovens. Provide a
minimum clearance of 12" (30.5 cm) above the unit that
is open to the front.
Door Removal
If the doors need to be removed during installation,
proceed as follows:
proceed as follows:
1.
Remove top hinge cover from hinge as shown
in Figure 4.
in Figure 4.
2.
Remove door from unit by lifting door up a few
inches and pulling away from unit.
inches and pulling away from unit.
Figure 3. Plug Configurations
Figure 4. Door Hinge Cover
Door
hinge
cover
hinge
cover