Milwaukee 5192 corded grinder Guía Del Usuario

• Keep work area clean and well lit. Cluttered or 

dark areas invite accidents.

pheres, such as in the presence of fl ammable 
liquids, gases or dust. Power tools create sparks 
which may ignite the dust or fumes.

operating a power tool. Distractions can cause 
you to lose control.

modify the plug in any way. Do not use any 
adapter plugs with earthed (grounded) power 
tools. Unmodifi ed plugs and matching outlets will 
reduce risk of electric shock.

surfaces such as pipes, radiators, ranges and 
refrigerators. There is an increased risk of electric 
shock if your body is earthed or grounded.

ditions. Water entering a power tool will increase 
the risk of electric shock.

carrying, pulling or unplugging the power tool. 
Keep cord away from heat, oil, sharp edges 
or moving parts. Damaged or entangled cords 
increase the risk of electric shock.

extension cord suitable for outdoor use. Use of 
a cord suitable for outdoor use reduces the risk of 
electric shock.

is unavoidable, use a residual current device 
(RCD) protected supply. Use of an RCD reduces 
the risk of electric shock.

common sense when operating a power tool. Do 
not use a power tool while you are tired or under 
the infl uence of drugs, alcohol or medication. A 
moment of inattention while operating power tools 
may result in serious personal injury.

wear eye protection. Protective equipment such 
as dust mask, non-skid safety shoes, hard hat, or 
hearing protection used for appropriate conditions 
will reduce personal injuries.

switch is in the off-position before connecting 
to power source and/or battery pack, picking 
up or carrying the tool. Carrying power tools with 
your fi nger on the switch or energising power tools 
that have the switch on invites accidents.

turning the power tool on. A wrench or a key left 
attached to a rotating part of the power tool may 
result in personal injury. 

balance at all times. This enables better control 
of the power tool in unexpected situations.

jewellery. Keep your hair, clothing and gloves 
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts. 

dust extraction and collection facilities, ensure 
these are connected and properly used. Use of 
dust collection can reduce dust-related hazards.

power tool for your application. The correct 
power tool will do the job better and safer at the 
rate for which it was designed.

turn it on and off. Any power tool that cannot be 
controlled with the switch is dangerous and must 
be repaired.

and/or the battery pack from the power tool 
before making any adjustments, changing 
accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of starting 
the power tool accidentally.

dren and do not allow persons unfamiliar with 
the power tool or these instructions to operate 
the power tool. Power tools are dangerous in the 
hands of untrained users.

or binding of moving parts, breakage of parts 
and any other condition that may affect the 
power tool’s operation. If damaged, have the 
power tool repaired before use. Many accidents 
are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly 

maintained cutting tools with sharp cutting edges 
are less likely to bind and are easier to control.

etc., in accordance with these instructions, 
taking into account the working conditions and 
the work to be performed. Use of the power tool 
for operations different from those intended could 
result in a hazardous situation.

repair person using only identical replacement 
parts. This will ensure that the safety of the power 
tool is maintained.

or its own cord. Cutting accessory contacting a 
live wire may make exposed metal parts of the 
power tool live and shock the operator.

• Position the cord clear of the spinning acces-

sory. If you lose control, the cord may be cut or 
snagged and your hand or arm may be pulled into 
the spinning accessory.

• Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning 
accessory may grab the surface and pull the power 
tool out of your control.

• Do not run the power tool while carrying it at 

your side. Accidental contact with the spinning 
accessory could snag your clothing, pulling the 
accessory into your body.

• Regularly clean the power tool’s air vents. The 

motor’s fan will draw the dust inside the housing 
and excessive accumulation of powdered metal 
may cause electrical hazards.

• Do not operate the power tool near fl ammable 

materials. Sparks could ignite these materials.

• Do not use accessories that require liquid 

coolants.  Using water or other liquid coolants 
may result in electrocution or shock.

Kickback and Related Warnings 
Kickback is a sudden reaction to a pinched or 
snagged rotating wheel, backing pad, brush or 
any other accessory. Pinching or snagging causes 
rapid stalling of the rotating accessory which in turn 
causes the uncontrolled power tool to be forced in 
the direction opposite of the accessory’s rotation 
at the point of the binding. 
For example, if an abrasive wheel is snagged or 
pinched by the workpiece, the edge of the wheel 
that is entering into the pinch point can dig into 
the surface of the material causing the wheel to 
climb out or kick out. The wheel may either jump 
toward or away from the operator, depending on 
direction of the wheel’s movement at the point of 
pinching. Abrasive wheels may also break under 
these conditions. 
Kickback is the result of power tool misuse and/or 
incorrect operating procedures or conditions and 
can be avoided by taking proper precautions as 
given below.
• Maintain a fi rm grip on the power tool and posi-

tion your body and arm to allow you to resist 
kickback forces. Always use auxiliary handle, 
if provided, for maximum control over kickback 
or torque reaction during start-up. The operator 
can control torque reactions or kickback forces, if 
proper precautions are taken.

• Never place your hand near the rotating acces-

sory. Accessory may kick back over your hand.

• Do not position your body in the area where 

power tool will move if kickback occurs. Kick-
back will propel the tool in direction opposite to 
the wheel’s movement at the point of snagging.

• Use special care when working corners, sharp 

edges etc. Avoid bouncing and snagging the 
accessory.  Corners, sharp edges or bouncing 
have a tendency to snag the rotating accessory 
and cause loss of control or kickback.

• Do not attach a saw chain woodcarving blade 

or toothed saw blade. Such blades create fre-
quent kickback and loss of control.

Safety Warnings Common for Die Grinding 
Operations: 
• This power tool is intended to function as a die 

grinder. Read all safety warnings, instructions, 
illustrations and specifi cations provided with 
this power tool. Failure to follow all instructions 
listed below may result in electric shock, fi re and/
or serious injury.

• Operations such as sanding, wire brushing, 

or polishing are not recommended to be 
performed with this power tool. Operations for 
which the power tool was not designed may create 
a hazard and cause personal injury.

• Do not use accessories which are not specifi -

cally designed and recommended by the tool 
manufacturer. Just because the accessory can 
be attached to your power tool, it does not assure 
safe operation.

• The rated speed of the accessory must be at 

least equal to the maximum speed marked on 
the power tool. Accessories running faster than 
their rated speed can break and fl y apart.

• The outside diameter and the thickness of your 

accessory must be within the capacity rating 
of your power tool. Incorrectly sized accessories 
cannot be adequately guarded or controlled.

• The arbour size of wheels, fl anges,  backing 

pads or any other accessory must properly 
fi t the spindle of the power tool. Accessories 
with arbour holes that do not match the mounting 
hardware of the power tool will run out of balance, 
vibrate excessively and may cause loss of control.

• Do not use a damaged accessory. Before each 

use inspect the accessory such as abrasive 
wheels for chips and cracks, backing pad for 
cracks, tear or excess wear, wire brush for 
loose or cracked wires. If power tool or acces-
sory is dropped, inspect for damage or install 
an undamaged accessory. After inspecting and 
installing an accessory, position yourself and 
bystanders away from the plane of the rotating 
accessory and run the power tool at maximum 
no-load speed for one minute. Damaged acces-
sories will normally break apart during this test time.

• Wear personal protective equipment. Depend-

ing on application, use face shield, safety 
goggles or safety glasses. As appropriate, 
wear dust mask, hearing protectors, gloves 
and work shop apron capable of stopping 
small abrasive or workpiece fragments. The 
eye protection must be capable of stopping 
fl ying debris generated by various operations. 
The dust mask or respirator must be capable of 
fi ltrating particles generated by your operation. 
Prolonged exposure to high intensity noise may 
cause hearing loss.

• Keep bystanders a safe distance away from 

work area. Anyone entering the work area 
must wear personal protective equipment. 
Fragments of workpiece or of a broken accessory 
may fl y away and cause injury beyond immediate 
area of operation.

• Hold power tool by insulated gripping surfaces