Oregon Scientific barm123a Manual De Usuario

7

GB

If no signals are received, blank “—-“ will be displayed.  Press and
hold  [SEARCH]  for  2  seconds  to  activate  search  for  the  remote
thermo signal from the sensor.

If that fails, check if the remote thermo sensor is still in place.  Try
repositioning  the  units  as  they  may  be  having  temperature  trans-
mission block as a result of interference.

Note: Failure of reception of remote signals may be due to the fol-
lowing reasons:

1. Battery power of the units is too low.

Suggested Solution: Replace with fresh batteries if necessary.

2. Batteries  may  freeze  when  the  temperature  falls  below  the

freezing point.  Frozen batteries will have a lower voltage and
therefore result in a shorter transmission range.

Suggested  Solution:  Shorten  the  transmission  range  by
repositioning the units.

3. Transmission path is blocked with obstacles and interference

from the surroundings.

Suggested Solution: Shorten the distance (e.g., move the main
unit closer to the window) or relocate the units when necessary.

The maximum and minimum indoor-remote temperatures recorded
will be automatically stored in memory.  Press [MEM] to toggle
among the current, maximum and minimum indoor and remote tem-
perature records.  The respective “MAX” or “MIN” indicator will
be shown.

To clear the memory, press and hold [MEM] for 2 seconds when
the maximum or minimum record is being displayed.  The memory
will be erased and replaced with current temperature until a new
maximum or minimum reading has been recorded.

If  the  temperature  readings  recorded  are  lower  or  higher  the
measuring range, “LLL” or “HHH” will be displayed respectively.

This unit gives a barometric pressure trend for the last hour.

Rising

SteadyFalling

BARM123A  detects  barometric  pressure  changes  and  displays
weather symbols including sunny, partly cloudy, cloudy, rainy and
snow that indicate weather forecasts for the next 12 to 24 hours.
The radius of the forecast is approximately 30 – 50 km or 18-30
miles.

sunnypartly

 cloudycloudy

rainysnow

This unit is also featured with a Soothing Sounds function which
can give out relaxing sounds continuously to mask the noise in the
surroundings.  There are 6 nature-simulating sounds which you can
choose from: (1) Bird sounds, (2) Wind sounds, (3) River sounds,
(4)  Rain  Drop  sounds  (5)  Waterfall  sounds  and  (6)  Ocean  Wave
sounds.

To  turn  on  the  Soothing  Sounds,  press  [POWER

].    Press

[RADIO/SOUND]  to  select  Soothing  Sounds  function.    Press
[SELECT] to toggle among the 6 different sounds.  The respective
LED will also light up to indicate the selected sound.

To  adjust  the  volume,  use  [VOLUME  ▲]  or  [VOLUME  ▼]  to
increase or decrease the volume.

To  turn  off  the  Soothing  Sounds,  press  [POWER ]  to  do  so  or
[RADIO/SOUND] to switch to Radio function.

To turn on the EL backlight of the LCD Display, press [SNOOZE/
LIGHT] to turn it on for 5 seconds.

Press [RESET] only in the following circumstances:

1. To enhance synchronization of signals after battery replacement

2. To reset the settings when the unit is malfunctioning

When  [RESET]  is  pressed,  all  settings  will  return  to  the  default
values and memory  records will be erased.

This unit is engineered to give you years of satisfactory service if
handled with care.

1. Do not immerse the unit into water.

2. Do note clean the unit with abrasive or corrosive materials.

3. Do not subject the unit to snow or excessive force, shock, dust,

temperature or humidity.

4. Do not tamper with the unit’s interal components.

5. Do  not  mix  new  and  old  batteries  or  batteries  of  different

specifications.