Fedders b3x05f2a Guía De Operación
4
OPERATION
ELECTRONIC CONTROLS
ELECTRONIC CONTROL PANEL
Power Control
The Power Control turns the unit on and off.
The Temperature/Hour Display
Shows the set temperature or the timer setting. THE TEMPERATURE DISPLAY ONLY SHOWS THE
SET TEMPERATURE, NOT THE ACTUAL ROOM TEMPERATURE.
SET TEMPERATURE, NOT THE ACTUAL ROOM TEMPERATURE.
Temperature/Hour Controls
These buttons are used to raise or lower the set temperature in increments of 1° from 66° to 88°.
They also raise or lower the hour setting in increments of 1 from 00 to 24 when the timer is being
set. In order to toggle between °F or °C, depress both of the controls at the same time.
They also raise or lower the hour setting in increments of 1 from 00 to 24 when the timer is being
set. In order to toggle between °F or °C, depress both of the controls at the same time.
Mode Control
The Mode Control has two settings:
FAN and COOL.
The settings are adjusted with the Mode Control button. A green light indicates which setting is
currently being used. When the COOL mode is selected, the unit will circulate and cool the air.
If the FAN mode is selected, the unit will only circulate the air.
currently being used. When the COOL mode is selected, the unit will circulate and cool the air.
If the FAN mode is selected, the unit will only circulate the air.
Fan Speed Control
The Fan Speed Control has three
settings:
settings:
High, Low and Auto. The settings are adjusted with the Fan Speed button, each time
the button is depressed it changes the
setting. A green light will indicate which setting is currently being used.
setting. A green light will indicate which setting is currently being used.
When the Auto feature is selected while the air conditioner is in the COOL mode, the fan speeds
will change automatically as the temperature in the room changes.
will change automatically as the temperature in the room changes.
• 4° or more above the set temperature the unit will be in HI FAN mode.
• 4° or less above the set temperature the unit will be in LO FAN mode.
Timer Control
The timer can be set to either turn the unit on or off.
To turn the unit on using the Timer:
•Depress the timer key when the power is off, the display will read 00. Adjust to the desired
number of hours before TURN ON using the up/down arrows.
•The display will show the time by hours left until TURN ON.
•To Turn the timer off, depress the timer key.
•A green light next to the Timer Control indicates that the timer is set.
To turn the unit OFF using the Timer:
•Depress the timer key when the power is on, the display will read 00. Adjust to the desired number of hours
before TURN OFF using the up/down arrows. The display will automatically go back to the set temperature
after 10 seconds.
after 10 seconds.
•To display the amount of time left until TURN OFF, depress the timer button once.
•To turn the TIMER OFF, depress the timer button twice.
•A green light next to the Timer Control indicates that the timer is set.
C
D
E
F
Power Control
Temperature/Timer Display
Temperature/Timer Controls
Mode Control
Fan Speed Control
Timer On/Off
A
B
C
D
E
F
A
B
C
D
E
F
A
B
Built-in three minute timing delay.
This electronic controlled unit will not
automatically resume operation after a
power failure.
automatically resume operation after a
power failure.
If this electronic unit will not respond to
touch pad or remote control commands,
it is necessary to unplug the unit from the
electrical outlet for five seconds and then
plug the unit back in.
touch pad or remote control commands,
it is necessary to unplug the unit from the
electrical outlet for five seconds and then
plug the unit back in.
The functions work the same as your air conditioner’s touch controls.
Air Conditioner Remote Control
AAA
IEC R03
1.5V
+
-
AAA
IEC R03
1.5V
6
7
CAUTION:
• Use only AAA or IEC R03 1.5V batteries.
• Remove the batteries if the remote controller is not used for a
• Use only AAA or IEC R03 1.5V batteries.
• Remove the batteries if the remote controller is not used for a
month or longer.
• Do not attempt to recharge the supplied batteries
• All batteries should be replaced at the same time.
• Do not dispose of the batteries in a fire as they may explode.
• Do not mix old and new batteries.
• Do not install the batteries with the polarity (+/–) reversed.
• Do not mix alkaline, standard (carbon - zinc), or rechargeable
• All batteries should be replaced at the same time.
• Do not dispose of the batteries in a fire as they may explode.
• Do not mix old and new batteries.
• Do not install the batteries with the polarity (+/–) reversed.
• Do not mix alkaline, standard (carbon - zinc), or rechargeable
(nickel-cadmium) batteries.
• Keep batteries and other things that could be swallowed away
from young children. Contact a doctor immediately if an
object is swallowed.
object is swallowed.