3com 3031 Instruccion De Instalación
Configuring X.25
307
After configuration, using the
display x25 switch-table pvc
command, you
can view the PVC table.
Adding/Deleting an SVC
Perform the following in the System View.
After configuration, using the
display x25 switch-table svc
command, you
can view the SVC table.
Configuring X.25 Load
Sharing
Overview of X.25 load sharing
Using the hunt group feature in X.25 protocol, network providers can provide the
load sharing function on X.25 packet switching network.X.25 load sharing can
implement the load sharing between different DTEs or between different links in
the same DTE, so as to ensure that link overload will not occur when a large
number of users access the same address.
load sharing function on X.25 packet switching network.X.25 load sharing can
implement the load sharing between different DTEs or between different links in
the same DTE, so as to ensure that link overload will not occur when a large
number of users access the same address.
X.25 load sharing is provided by DCE. To implement load sharing on X.25
network, you need to configure a set of DTE/DCE interfaces (synchronous serial
interface or XOT channel) as a hunt group on the remote DCE, and to assign an
X.121 address to this hunt group. When accessing the DTE in hunt group, other
devices in the network need to call the hunt group address. After receiving call
request packet, the remote DCE will select a line from hunt group and send
incoming call packet based on different channel selection policies (round-robin or
vc-number). Different calls will be distributed on various lines in hunt group, so as
to implement load sharing.
network, you need to configure a set of DTE/DCE interfaces (synchronous serial
interface or XOT channel) as a hunt group on the remote DCE, and to assign an
X.121 address to this hunt group. When accessing the DTE in hunt group, other
devices in the network need to call the hunt group address. After receiving call
request packet, the remote DCE will select a line from hunt group and send
incoming call packet based on different channel selection policies (round-robin or
vc-number). Different calls will be distributed on various lines in hunt group, so as
to implement load sharing.
Note that X.25 hunt group selects different transmission lines only during VC call
establishment. Once the whole VC completes the establishment and enters data
transfer phase, X.25 hunt group will not function any longer and data transfer will
be processed based on the normal VC. Since PVC is in data transfer phase after
establishment and has not experienced call establishment and call clearing
processes, X.25 load sharing can function only on SVC, and not on PVC.
establishment. Once the whole VC completes the establishment and enters data
transfer phase, X.25 hunt group will not function any longer and data transfer will
be processed based on the normal VC. Since PVC is in data transfer phase after
establishment and has not experienced call establishment and call clearing
processes, X.25 load sharing can function only on SVC, and not on PVC.
In an X.25 hunt group, the position of all DTEs is identical, and they have the same
X.121 address. DTEs inside hunt group can call other DTEs outside hunt group
according to the normal mode. When accessing hunt group, the devices outside
X.121 address. DTEs inside hunt group can call other DTEs outside hunt group
according to the normal mode. When accessing hunt group, the devices outside
Table 373 Adding/Deleting a PVC route
Operation
Command
Add a PVC
x25 switch pvc number channel interface serial
port-number pvc number
port-number pvc number
Delete a PVC
undo x25 switch pvc number
Table 374 Adding/Deleting an SVC
Operation
Command
Add an SVC
x25 switch svc x.121-address [ sub-dest
destination-address ] [ sub-source source-address ]
interface serial interface-number
destination-address ] [ sub-source source-address ]
interface serial interface-number
Delete a SVC
undo x25 switch svc x.121-address [ sub-dest
destination-address ] [ sub-source source-address ] [
interface serial interface-number ]
destination-address ] [ sub-source source-address ] [
interface serial interface-number ]