Samsung CLP-600 Guía Del Usuario
Using Your Printer on a Network (CLP-600N only)
8.5
• Security Mode: “None”, “Static WEP”, or “Enhanced” The
Samsung print server provides three kinds of Security Modes
(such as “None” Static WEP, and Enhanced) for easy setting
of wireless network security. “None” security mode is used
when the validation of wireless device's identity and data
encryption are not required for your network. Static WEP
uses WEP (Wired Equivalent Privacy) algorithm suggested by
IEEE802.11 standard for security. A WEP algorithm provides
data encryption and decryption for data communication.
Static WEP security requires WEP key for data encryption,
decryption, and authentication. Enhanced provides more
security and better key management than Static WEP by
using IEEE802.1X EAP authentication and dynamic
encryption (such as dynamic WEP, TKIP, AES). Enhanced
cannot be configured on printer's control panel. In order to
choose Enhanced as security mode, you must use SWS
(Syncthru Web Service). For more information about
Enhanced settings, see the Network Printer User’s Guide.
The default setting is “None”.
(such as “None” Static WEP, and Enhanced) for easy setting
of wireless network security. “None” security mode is used
when the validation of wireless device's identity and data
encryption are not required for your network. Static WEP
uses WEP (Wired Equivalent Privacy) algorithm suggested by
IEEE802.11 standard for security. A WEP algorithm provides
data encryption and decryption for data communication.
Static WEP security requires WEP key for data encryption,
decryption, and authentication. Enhanced provides more
security and better key management than Static WEP by
using IEEE802.1X EAP authentication and dynamic
encryption (such as dynamic WEP, TKIP, AES). Enhanced
cannot be configured on printer's control panel. In order to
choose Enhanced as security mode, you must use SWS
(Syncthru Web Service). For more information about
Enhanced settings, see the Network Printer User’s Guide.
The default setting is “None”.
•
Authentication: “Open System” or “Shared Key”. This
option is available in Static WEP mode only. If required by
your network, the proper authentication method must be
configured on the print server. The default setting is “Open
System”.
option is available in Static WEP mode only. If required by
your network, the proper authentication method must be
configured on the print server. The default setting is “Open
System”.
•
Encryption: “64-bit WEP” or “128-bit WEP”. This option is
available in Static WEP mode only. If your network uses
Static Encryption keys, you must configure the Encryption
keys. You can configure up to four keys. The active key must
match the value and active key position (for example, Key 1)
configured on other wireless devices. The default setting is
“64-bit WEP”.
available in Static WEP mode only. If your network uses
Static Encryption keys, you must configure the Encryption
keys. You can configure up to four keys. The active key must
match the value and active key position (for example, Key 1)
configured on other wireless devices. The default setting is
“64-bit WEP”.
•
Using Key: Select the key to use in your network. This
option is available in Static WEP mode only. The default
setting is “Key 1”.
option is available in Static WEP mode only. The default
setting is “Key 1”.
• Key Type: Select the key type of your network. This option
is available in Static WEP mode only. The default setting is
“Hexadecimal”.
“Hexadecimal”.
• Key1, Key2, Key3, Key4: Enter the key number for
“
Encryption”. This option is available in Static WEP mode
only. The default setting is 0 for all keys. The numbers you
can enter are as follows:
can enter are as follows:
N
OTE
: Your changes for wireless parameters will be applied
after resetting the print server. In order to reset the print
server, see “Rebooting the Network Interface Card” on
page 8.4.
server, see “Rebooting the Network Interface Card” on
page 8.4.
Hexadecimal
Alphanumeric
64-bit WEP
10 digits
5 characters
128-bit WEP
26digits
13 characters
Restoring the Wireless Configuration
You can return the wireless configuration only to its default
settings.
settings.
1
In ready mode, press the Menu button (
) until you see
“Network” on the bottom line of the display. Press the
Enter button (
Enter button (
) to access the menu.
2
Press the Enter button (
) when “Config Network”
displays on the bottom line.
3
Press the scroll button (
or
) until “Yes” displays on
the bottom line. Press the Enter button (
).
4
Press the Upper Level button (
).
5
Press the scroll button (
or
) until “Config WLAN”
displays on the bottom line. Press the Enter button (
).
6
Press the scroll button (
or
) until “Yes” displays on
the bottom line. Press the
Enter button (
).
7
Press the Upper Level button (
).
8
Press the scroll button (
or
) until “WLAN Default”
displays on the bottom line.
9
Press the Enter button (
) to confirm the selection.
N
OTE
: This feature will be applied after resetting the print
server. In order to reset the print server, see “Rebooting the
Network Interface Card” on page 8.4.
Network Interface Card” on page 8.4.