Polycom IP 600 Guía Del Usuario
2
Installing SoundPoint
®
IP 600/601 SIP
This section provides basic installation
instructions and information for obtaining
the best performance with the Sound-
Point
instructions and information for obtaining
the best performance with the Sound-
Point
®
IP 600/601 SIP phone. If you re-
quire additional information or assistance
with your new phone, please contact your
system administrator.
with your new phone, please contact your
system administrator.
The SoundPoint
®
IP 600/601 SIP User
Guide includes regulatory compliance
information that your system administra-
tor should review and can also be found at
www.polycom.com.
information that your system administra-
tor should review and can also be found at
www.polycom.com.
Powering Options for the SoundPoint
®
IP 600/601
Both the SoundPoint
®
IP 600 and SoundPoint
®
IP 601 can be powered
from Power over Ethernet in addition to AC power sources.
For Power over Ethernet, both models will accept power over stan-
dards-based IEEE802.3af and pre-standard Cisco Power over Ethernet
via the used or unused pairs over the Ethernet cables plugged ino the
LAN port.
For AC power source, both models are shipped with an adapter to
convert the AC voltage to the appropriate DC voltage required.
For Power over Ethernet, both models will accept power over stan-
dards-based IEEE802.3af and pre-standard Cisco Power over Ethernet
via the used or unused pairs over the Ethernet cables plugged ino the
LAN port.
For AC power source, both models are shipped with an adapter to
convert the AC voltage to the appropriate DC voltage required.
► There are differences between the DC voltages required by the SoundPoint
®
IP 600 and IP 601:
Requires a 12VDC rated power adapter as
supplied in the original packaging. Power
over Ethernet under the IEEE802.3af
standard also supplies sufficient wattage
to power the SoundPoint
supplied in the original packaging. Power
over Ethernet under the IEEE802.3af
standard also supplies sufficient wattage
to power the SoundPoint
®
IP 600 phone
without use of the adapter above. Power-
ing under the pre-standard Cisco Power
over Ethernet will also supply sufficient
wattage to power the SoundPoint
over Ethernet will also supply sufficient
wattage to power the SoundPoint
®
IP 600
phone.
SoundPoint
®
IP 601
Requires a 24VDC rated power adapter as
supplied in the original packaging. The
24VDC adapter supplies sufficient wattage
to power the SoundPoint
supplied in the original packaging. The
24VDC adapter supplies sufficient wattage
to power the SoundPoint
®
IP 601 phone
and up to three SoundPoint
®
IP Expansion
Modules (optional accessories). Power
over Ethernet under the IEEE802.3af
over Ethernet under the IEEE802.3af
standard also supplies sufficient wattage
to power the SoundPoint
to power the SoundPoint
®
IP 601 phone
and up to three SoundPoint
®
IP Expansion
Modules. At time of writing, powering
under the pre-standard Cisco Power over
Ethernet will supply sufficient wattage to
power the SoundPoint
under the pre-standard Cisco Power over
Ethernet will supply sufficient wattage to
power the SoundPoint
®
IP 601 phone only.
When powering from an AC voltage source,
it is important to use only that power adapter
that shipped with the appropriate phone
it is important to use only that power adapter
that shipped with the appropriate phone
.
Powering a SoundPoint® IP 600 phone from
a SoundPoint® IP 601 phone adapter, or
a SoundPoint® IP 601 phone adapter, or
vice-versa, cannot guarantee correct operation
over all input conditions. If in doubt about
the appropriate power adapter that ships with
your unit, contact your system administrator
for futher details and/or options.
over all input conditions. If in doubt about
the appropriate power adapter that ships with
your unit, contact your system administrator
for futher details and/or options.
SoundPoint
®
IP 600