Boss Audio 639ua Guía Del Usuario
- 3 -
- 14 -
Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up
properly and the unit and system work properly.
Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts
can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the
vehicle.
Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
If installation angle exceeds 30 from horizontal, the unit might not give its optimum performance.
properly and the unit and system work properly.
Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts
can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the
vehicle.
Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
If installation angle exceeds 30 from horizontal, the unit might not give its optimum performance.
Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or
from hot air, from heater, or where it would be subject to dust dirt or excessive vibration.
Be sure to remove the front panel before installing the unit.
from hot air, from heater, or where it would be subject to dust dirt or excessive vibration.
Be sure to remove the front panel before installing the unit.
DIN FRONT/REAR-MOUNT
This unit can be property installed either from Front (conventional DIN Front-mount) or Rear (DIN
Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For
details, refer to the following illustrated installation methods A and B.
Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For
details, refer to the following illustrated installation methods A and B.
DIN FRONT-MOUNT (Method A)
Installation the unit
1. Dashboard
2. Holder
2. Holder
After inserting the half sleeve into the
dashboard, select the appropriate tab according
to the thickness of the dashboard material and
bend them inwards to secure the holder in
place.
dashboard, select the appropriate tab according
to the thickness of the dashboard material and
bend them inwards to secure the holder in
place.
3. Screw
30
1
3
2
4
5
1. Dashboard
2. Nut (5mm)
3. Screw (5x15mm)
4. Screw
5. Support Strap
Be sure to use the support strap to secure the
2. Nut (5mm)
3. Screw (5x15mm)
4. Screw
5. Support Strap
Be sure to use the support strap to secure the
back of the unit in place. The strap can be bent
by hand to the desired angle.
by hand to the desired angle.
182
53
1
2
3
Installation
Setting Mode
You can make changes to the system setting in the following area:
Radio Frequency Range + Enable/Disable AUX In + Clock Format
The display will show TEST MOD
breifly to indicate you are in
system setting area and then automatically change to Radio Frequency
selection mode. At any time, you can press the > button to step through
the above areas. When you are ready to leave the System Setting area,
press ENTER. The unit will reboot to initialize with the new setting.
selection mode. At any time, you can press the > button to step through
the above areas. When you are ready to leave the System Setting area,
press ENTER. The unit will reboot to initialize with the new setting.
- Radio Settings
The unit can operate on serveral different frequency ranges. Please see
the following for these ranges. The default frequency range is
The unit can operate on serveral different frequency ranges. Please see
the following for these ranges. The default frequency range is
AMERICAN 2
.
To change the range to suit your location, press DOWN ARROW until
the desired frequency range is hight lighted. The press > to save it and
move to next setting area.
the desired frequency range is hight lighted. The press > to save it and
move to next setting area.
-AUX Input Enable/Disable
Press DOWN ARROW to move between Enable and Disable modes.
When the selection has been made, press > to save it and move to
next setting area or press ENTER to leave the System Setting mode.
Press DOWN ARROW to move between Enable and Disable modes.
When the selection has been made, press > to save it and move to
next setting area or press ENTER to leave the System Setting mode.
-Clock Format (12-hour or 24-hour)
Press DOWN ARROW to move between 12-hour and 24-hour format,
press > to save it and move to next setting area or press ENTER to
leave the System Setting mode.
Press DOWN ARROW to move between 12-hour and 24-hour format,
press > to save it and move to next setting area or press ENTER to
leave the System Setting mode.
If Aux Input is disable in System Settings, any input connected will not
be played.
be played.
AMERICAN 1
AMERICAN 2
EUROPE 10
EUROPE 5
MID EAST
AUST (AUSTRALIA)
RUSSIA
JAPAN
AMERICAN 2
EUROPE 10
EUROPE 5
MID EAST
AUST (AUSTRALIA)
RUSSIA
JAPAN
FM:87.5-108MHz
FM:87.5-107.9MHz
FM:87.5-108MHz
FM:87.5-108MHz
FM:87.5-108MHz
FM:87.5-108MHz
FM:65.0-74MHz
FM:76.0-90.0MHz
FM:87.5-107.9MHz
FM:87.5-108MHz
FM:87.5-108MHz
FM:87.5-108MHz
FM:87.5-108MHz
FM:65.0-74MHz
FM:76.0-90.0MHz
AM:530-1710kHz
AM:530-1710kHz
AM:522-1620kHz
AM:522-1620kHz
AM:531-1602kHz
AM:522-1593kHz
AM:522-1620kHz
AM:522-1629kHz
AM:530-1710kHz
AM:522-1620kHz
AM:522-1620kHz
AM:531-1602kHz
AM:522-1593kHz
AM:522-1620kHz
AM:522-1629kHz
BAND NAME FREQUENCYRANGE