Bunn ICB Guía Del Usuario

Page 35

ENABLE ADS
This function allows the operator to choose whether 
or not to display an advertising message. An ad can be 
saved to the brewer by either writing the ad using the 
programming commands, or by entering the ad into 
the brewer using an AD CARD. This message will be 
displayed when the brewer is not in use.

Procedure to Enable/Disable Ads:
1.  Press and hold the right hidden button until the 

display reads SET LANGUAGE. Press the right hid-
den button until the display reads ENABLE ADS. The 
YES or NO will be fl ashing to indicate the current 
selection.

2.  Press and release the NO button to disable this 

function, or:

3.  Press and release the YES  button to enable this 

function.

4.  When fi nished, press and release DONE to save 

the new setting and advance to the next function 
screen.  

5. If NO was selected, the display should now read 

ENABLE SANITATION. To exit programming and 
return to the MAIN SCREEN, press and release the 
ON/OFF pad.

6. If YES was selected, the display should now read 

NEW AD?.  This screen allows the operator to 
select between using an ad card to read in a new 
ad, writing an ad, or using the ad currently stored 
in the brewer’s memory (if an ad was previously 
saved).

Procedure to WRITE an Ad:
NOTE:  Writing and saving a new ad will erase any 
previously saved ad in the brewer’s memory.

7. From the NEW AD? screen, press and release 

WRITE.  

8.  The display should now read 2 LINES 16 CHARS 

AVAILABLE, and then SCROL THRU ALPHA, NEXT 
-> NEXT LETTER, and then WRITE TOP LINE?. The 
ad can be up to 32 characters long, 16 per line. The 
ad will be written in two steps, fi rst the top line, 
then the bottom line.

9.  To write the top line of a new ad, press and release 

YES. To skip the top line and only write a bottom 
line, press and release NO  and proceed to step 
13.  To exit programming and return to the MAIN 
SCREEN, press and release the ON/OFF pad.

10. The display will now read A with a fl ashing cursor 

below it. Press and hold the SCROLL button to scroll 
through the alphabet and available characters. When 
the desired character is shown on the display, press 
and release NEXT to move to the next character in 
the top line. 

11. Repeat step 10 until the top line is complete.
12. Press and release DONE. The display should now 

read WRITE BTM LINE?.

13. To write the bottom line of the new ad, press and 

release YES.  

14. To skip the bottom line, press and release NO.
 

a.  If neither a top nor bottom line was written, the 
display should now read ENABL SANITATION.  

 

b.  If only a top line was written, the ad will be 
displayed followed by SAVE? Proceed to step 18.  

15. The display will now read A with a fl ashing cursor 

below it.  Press and hold the SCROLL button to 
scroll through the alphabet and available charac-
ters.  When the desired character is shown on the 
display, press and release NEXT to move to the next 
character in the bottom line. 

16. Repeat step 15 until the bottom line is complete.
17. Press and release DONE.  The display will now show 

the written ad, and then SAVE?

18. To cancel saving the ad, press and release NO.  

The display should now read ADVERTISEMENT 
NOT SAVED! and then will return to the NEW AD 
screen.  To exit programming and return to the MAIN 
SCREEN, press and release the ON/OFF pad.

19. To correct or edit the ad, press and release EDIT.  

The display should now read WRITE TOP LINE?  
Repeat steps 10 though 17.

20. To save the ad as it is shown, press and release 

YES.  The display should now read ADVERTISE-
MENT SETUP COMPLETE, and then ENABL SANITA-
TION.  To exit programming and return to the MAIN 
SCREEN, press and release the ON/OFF pad.

37077 091704