Bunn TW Guía Del Usuario
Page 22
TL1 - WHI/VIO to Iced Tea Solenoid and
WHI/VIO to TEA/OFF/COFEE Switch
TL2 - WHI to Power Cord (120V Models) or
WHI to Terminal Block (120/208V Models)
TL3 - ORN to START Switch
TL4 - WHI/BLU to Iced Tea Solenoid
TL5 - YEL to START Switch
WHI/VIO to TEA/OFF/COFEE Switch
TL2 - WHI to Power Cord (120V Models) or
WHI to Terminal Block (120/208V Models)
TL3 - ORN to START Switch
TL4 - WHI/BLU to Iced Tea Solenoid
TL5 - YEL to START Switch
FIG. 13 DIGITAL TIMER WIRING
P2037
SERVICE (cont.)
DIGITAL BREW TIMER (ICED TEA - Late
Models)(cont.)
Models)(cont.)
1. Modifying brew volumes. To modify a brew vol-
ume, first check that the SET/LOCK switch is in the
“SET” position on the circuit board.
ume, first check that the SET/LOCK switch is in the
“SET” position on the circuit board.
To increase a brew volume, place the TEA/OFF/
COFFEE switch in the “TEA” position, press and hold
the START switch until three clicks are heard. Release
the switch and press it again one or more times. (Fail-
ure to release the switch within two seconds after the
third click causes the volume setting to be aborted
and previous volume setting will remain in memory.)
Each time the switch is pressed, two seconds are
added to the brew time period. Allow the brew cycle
to finish in order to verify that the desired volume has
been achieved.
the START switch until three clicks are heard. Release
the switch and press it again one or more times. (Fail-
ure to release the switch within two seconds after the
third click causes the volume setting to be aborted
and previous volume setting will remain in memory.)
Each time the switch is pressed, two seconds are
added to the brew time period. Allow the brew cycle
to finish in order to verify that the desired volume has
been achieved.
To decrease a brew volume, place the TEA/OFF/
COFFEE switch in the “TEA” position, press and re-
lease the START switch once for every two-second
interval to be removed from the total brew time pe-
riod; then immediately press and hold down the START
switch until three clicks are heard. Release the switch.
(Failure to release the switch within two seconds af-
ter the third click causes the volume setting to be
aborted and previous volume setting will remain in
memory). Allow the brew cycle to finish in order to
verify that the desired volume has been achieved.
lease the START switch once for every two-second
interval to be removed from the total brew time pe-
riod; then immediately press and hold down the START
switch until three clicks are heard. Release the switch.
(Failure to release the switch within two seconds af-
ter the third click causes the volume setting to be
aborted and previous volume setting will remain in
memory). Allow the brew cycle to finish in order to
verify that the desired volume has been achieved.
2. Setting brew volumes. To set a brew volume,
first check that the SET/LOCK switch is in the “SET”
position on the circuit board. Place the TEA/OFF/COF-
FEE switch in the “TEA” position, press and hold the
START switch until three distinct clicks are heard and
then release the switch. (Failure to release the switch
within two seconds after the third click causes the
volume setting to be aborted and previous volume
setting will remain in memory.)
View the level of the liquid being dispensed. When
the desired level is reached, turn the TEA/OFF/COF-
FEE switch to “OFF”.
first check that the SET/LOCK switch is in the “SET”
position on the circuit board. Place the TEA/OFF/COF-
FEE switch in the “TEA” position, press and hold the
START switch until three distinct clicks are heard and
then release the switch. (Failure to release the switch
within two seconds after the third click causes the
volume setting to be aborted and previous volume
setting will remain in memory.)
View the level of the liquid being dispensed. When
the desired level is reached, turn the TEA/OFF/COF-
FEE switch to “OFF”.
NOTE: Several ounces of water will continue to sy-
phon from the tank after turning the switch “OFF”.
The brewer remembers this volume and will continue
to brew batches of this size until the volume setting
procedure is repeated.
NOTE: When brewing coffee, volume will decrease due
to absorption by the coffee grounds.
phon from the tank after turning the switch “OFF”.
The brewer remembers this volume and will continue
to brew batches of this size until the volume setting
procedure is repeated.
NOTE: When brewing coffee, volume will decrease due
to absorption by the coffee grounds.
3. Setting programming disable feature. If it be-
comes necessary to prevent anyone from changing
brew time once programmed, you can set the SET/
LOCK switch to the “LOCK” position. This will pre-
vent any further programming until switch is once
again put into the “SET” position.
comes necessary to prevent anyone from changing
brew time once programmed, you can set the SET/
LOCK switch to the “LOCK” position. This will pre-
vent any further programming until switch is once
again put into the “SET” position.
10510 071000