Epson 7850p Hoja De Datos Del Producto
EPSON PowerLite 7850p Projector
6/03
EPSON PowerLite 7850p Projector
-
15
12. Verify that you’ve enabled your computer’s connection to
the access point. It should be listed as shown above, with
the small icon
the small icon
next to it, indicating a connection.
If it’s not listed, click
Configure
and then type the name of
your access point.
13. When done, click
OK
. Continue with “Projecting
Checking the Gateway IP Address
If you’re entering IP addresses manually in Access Point mode
and need to find out the gateway IP address (the IP address of
your access point), make sure the wireless connection to the
access point is currently active, as described in the previous
section.
and need to find out the gateway IP address (the IP address of
your access point), make sure the wireless connection to the
access point is currently active, as described in the previous
section.
Note: If you can’t identify the gateway address using this
Windows utility, use the administrator’s utility software that
came with your access point.
Windows utility, use the administrator’s utility software that
came with your access point.
1. Access your wireless network Properties window. For
example, in Windows XP click
Start > Control Panel >
Network and Internet Connections
. Then
double-click the
Network Connections
icon.
2. Right-click the
Wireless Network Connection
icon and
select
Status
. Then click the
Support
tab.
The gateway’s (access point’s) IP address is listed as shown:
Projecting Wirelessly
Once you’ve started EasyMP and set up your projector and
computer in either Ad Hoc mode or Access Point mode,
follow these steps to start NS Connection and project
wirelessly.
computer in either Ad Hoc mode or Access Point mode,
follow these steps to start NS Connection and project
wirelessly.
Note: You must have installed EMP NS Connection from your
projector CD-ROM. See the User’s Guide for installation
instructions.
projector CD-ROM. See the User’s Guide for installation
instructions.
1. Make sure you’ve inserted the EPSON 802.11b card in the
projector’s card slot (see page 11). Then select
EMP NS
Connection
from the Windows Start menu.
The first time you start NS Connection, you see a dialog
box asking you to select your network. Select the IP address
for your computer’s network adapter card and click
box asking you to select your network. Select the IP address
for your computer’s network adapter card and click
OK
.
Note: If you don’t see your network adapter’s IP address,
allow a minute for it to appear. If your access point uses
DHCP, sometimes it takes a minute for the server to pick up
the IP address.
allow a minute for it to appear. If your access point uses
DHCP, sometimes it takes a minute for the server to pick up
the IP address.
You see the screen below. (If you have previously started
NS Connection, this is the first screen you see.)
NS Connection, this is the first screen you see.)
Note: Once you’ve selected the IP address for your network
adapter, you won’t see the Switch network dialog box when
you start NS Connection. If you want to change to a different
network adapter, click
adapter, you won’t see the Switch network dialog box when
you start NS Connection. If you want to change to a different
network adapter, click
Extension
on the EMP NS
Connection dialog box, then click
Switch LAN
.
If the connection is working properly, you see your
projector listed. If you have additional projectors on the
network, they are also listed, along with their status. The
color of the status icon next to each projector’s name
indicates its status:
❏ Gray: the projector is not connected
❏ Orange: the projector is connected to another
projector listed. If you have additional projectors on the
network, they are also listed, along with their status. The
color of the status icon next to each projector’s name
indicates its status:
❏ Gray: the projector is not connected
❏ Orange: the projector is connected to another
computer
❏ Green: the projector is connected to your computer
Gateway
address
address