Juniper SSG-140-SH Prospecto
Getting Started Guide
CONFIGURING THE DEVICE
Use the instructions below to start the Initial Configuration Wizard (ICW), which helps
you to configure the device to protect your network.
you to configure the device to protect your network.
Step 1
Launch a browser. In the URL address field, enter
http://192.168.1.1
http://192.168.1.1
. The Rapid Deployment Wizard window
appears.
Step 2
Login to the WebUI. The default admin name is netscreen, and the
default admin password is netscreen.
Note:
default admin password is netscreen.
Note:
You can access the ICW from the Ethernet port 0/0, which is
bound to the Trust security zone.
Step 3
If your network uses Juniper Networks NetScreen-Security Manager,
you can use a Rapid Deployment configlet to automatically configure
the device. Obtain a configlet from your NetScreen-Security
Manager administrator, select Yes, select Load Configlet from: ,
browse to the file location, then click Next. The configlet sets up the
device for you.
you can use a Rapid Deployment configlet to automatically configure
the device. Obtain a configlet from your NetScreen-Security
Manager administrator, select Yes, select Load Configlet from: ,
browse to the file location, then click Next. The configlet sets up the
device for you.
If you want to bypass the configuration wizard and go directly to the
WebUI, select the last option, then click Next.
WebUI, select the last option, then click Next.
If you are not using a configlet to configure the device and want to
use the ICW, select the first option, then click Next. The Initial
Configuration Wizard welcome screen appears. Click Next.
use the ICW, select the first option, then click Next. The Initial
Configuration Wizard welcome screen appears. Click Next.
To continue configuring your device with the ICW, refer to Appendix
B in the SSG 140 Hardware Installation and Configuration Guide.
B in the SSG 140 Hardware Installation and Configuration Guide.
By default ethernet0/0 is bound to the Trust zone and has the IP
address 192.168.1.1/24. You can connect the SSG 140 device to
your trusted network with any ports that are bound to this interface.
To change the interface bindings, refer to the SSG 140 Hardware
Installation and Configuration Guide.
The following table explains the default interface-to-zone binding.
address 192.168.1.1/24. You can connect the SSG 140 device to
your trusted network with any ports that are bound to this interface.
To change the interface bindings, refer to the SSG 140 Hardware
Installation and Configuration Guide.
The following table explains the default interface-to-zone binding.
Label
Interface
Zone
10/100 Ethernet ports:
0/0
ethernet0/0 Trust
0/1
ethernet0/1
DMZ
0/2
ethernet0/2
Untrust
0/3
ethernet0/3
Null
0/4
ethernet0/4
Null
0/5
ethernet0/5
Null
0/6
ethernet0/6
Null
0/7
ethernet0/7
Null
10/100/1000 Gigabit Ethernet ports:
0/8
ethernet0/8
Null
0/9
ethernet0/9
Null
Copyright © 2006 Juniper Networks, Inc. All rights reserved. Juniper Networks, the Juniper Networks logo, NetScreen, NetScreen Technologies, GigaScreen, NetScreen-Global PRO,
NetScreen-Remote, NetScreen ScreenOS and the NetScreen logo are trademarks and registered trademarks of Juniper Networks, Inc. in the United States and other countries. All other
trademarks and registered trademarks are the property of their respective companies. Information in this document is subject to change without notice. No part of this document may
be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without receiving written permission from Juniper Networks, Inc.
NetScreen-Remote, NetScreen ScreenOS and the NetScreen logo are trademarks and registered trademarks of Juniper Networks, Inc. in the United States and other countries. All other
trademarks and registered trademarks are the property of their respective companies. Information in this document is subject to change without notice. No part of this document may
be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without receiving written permission from Juniper Networks, Inc.
P/N 530-015645-01 rev 01B