Craftsman 54915 Manual De Usuario
Motion-Detecting Control Panel Setup
NOTE: If the command LED is
continuously blinking, the Lock
feature needs to be deactivated.
continuously blinking, the Lock
feature needs to be deactivated.
ON
Button
Button
OFF
Button
Button
HOLD OPEN
Button
Button
LOCK Button
Command LED
Motion
Sensor
Switch
Sensor
Switch
Motion
Sensor
Sensor
LEARN Button
LIGHT Button
1 Minute,
5 Minute,
and 10 Minute
TTC LED
5 Minute,
and 10 Minute
TTC LED
TIMER-TO-CLOSE (TTC)
NOTE: DO NOT enable TTC if operating a one-piece door. TTC is to
be used ONLY with sectional doors.
Activate:
Press and hold the ON button until one of the TTC LEDs light up.
Then press the ON button again to cycle through the time interval
options (the corresponding TTC LED will light for each time
interval). The garage door opener light bulbs will blink as
confirmation.
NOTE: DO NOT enable TTC if operating a one-piece door. TTC is to
be used ONLY with sectional doors.
Activate:
Press and hold the ON button until one of the TTC LEDs light up.
Then press the ON button again to cycle through the time interval
options (the corresponding TTC LED will light for each time
interval). The garage door opener light bulbs will blink as
confirmation.
Deactivate:
Press and hold the OFF button until all TTC LEDs turn off and a
beep is heard from the motor unit.
Press and hold the OFF button until all TTC LEDs turn off and a
beep is heard from the motor unit.
Temporarily hold door open (suspend TTC):
Press and release the HOLD OPEN button. Press the HOLD OPEN
button again to resume normal TTC operation.
Press and release the HOLD OPEN button. Press the HOLD OPEN
button again to resume normal TTC operation.
LOCK
Activate:
Press and hold the LOCK button for 2 seconds. The command
LED will flash as long as the lock feature is activated and your
hand held remote control will not operate your door at this time.
Activate:
Press and hold the LOCK button for 2 seconds. The command
LED will flash as long as the lock feature is activated and your
hand held remote control will not operate your door at this time.
Deactivate:
Press and hold the LOCK button again for 2 seconds. The
command LED will stop flashing and normal operation will
resume.
Press and hold the LOCK button again for 2 seconds. The
command LED will stop flashing and normal operation will
resume.
LIGHT
To change the amount of time the garage door opener lights
will stay on:
Press and hold the LOCK button until the garage door opener
lights flash.* The time interval is indicated by the number of
flashes.
To change the amount of time the garage door opener lights
will stay on:
Press and hold the LOCK button until the garage door opener
lights flash.* The time interval is indicated by the number of
flashes.
NUMBER OF TIMES GARAGE
DOOR OPENER LIGHTS FLASH
TIME THE GARAGE DOOR
OPENER LIGHT STAYS ON
1
1 ½ Minutes
2
2 ½ Minutes
3
3 ½ Minutes
4
4 ½ Minutes
To cycle through the time intervals repeat the step above.
LIGHT FEATURE
This feature will turn on the garage door opener lights when the
safety reversing sensors have been broken.
This feature will turn on the garage door opener lights when the
safety reversing sensors have been broken.
Deactivate:
Press and hold the LIGHT button until the garage door opener
lights turn on, then off again.*
Press and hold the LIGHT button until the garage door opener
lights turn on, then off again.*
Activate:
Start with the garage door opener lights on. Press and hold the
LIGHT button until the garage door opener lights turn off, then on
again.*
Start with the garage door opener lights on. Press and hold the
LIGHT button until the garage door opener lights turn off, then on
again.*
MOTION SENSOR
Activate/Deactivate:
Slide the motion sensor switch ON or OFF.
Activate/Deactivate:
Slide the motion sensor switch ON or OFF.
* Approximately 10 seconds
33